Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2019.07
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278195 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B2416  Height Control Sensor Malfunction  


DESCRIPTION

This DTC is stored when the headlight leveling ECU assembly detects a malfunction in the rear height control sensor sub-assembly power source or rear height control sensor sub-assembly.

DTC No. Detection Item DTC Detecting Condition Trouble Area DTC Output from
B2416 Height Control Sensor Malfunction
·

Malfunction in rear height control sensor sub-assembly

·

Open or short in rear height control sensor sub-assembly power source circuit


·

Rear height control sensor sub-assembly

·

Harness or connector

·

Headlight leveling ECU assembly


Headlight leveling ECU assembly

WIRING DIAGRAM

E370854E39
4.083,2.292 6.396,2.49 2.313,0.198 10 false Headlight Leveling ECU Assembly 4.083,2.125 4.448,2.292 0.365,0.167 10 false A34 2.854,1.51 3.146,1.76 0.292,0.25 10 false 1 2.854,1 3.146,1.25 0.292,0.25 10 false 2 2.854,0.49 3.146,0.74 0.292,0.25 10 false 3 4.979,0.344 5.271,0.594 0.292,0.25 10 false 5 V 2.427,0.594 2.979,0.854 0.552,0.26 10 false SHB 2.333,1.115 3.417,1.417 1.083,0.302 10 false SHRR 2.417,1.615 3.219,1.917 0.802,0.302 10 false SHG 0.604,2.115 0.854,2.313 0.25,0.198 10 false R1 0.594,2.292 3.24,2.5 2.646,0.208 10 false Rear Height Control Sensor Sub-assembly 4.115,1.51 4.406,1.76 0.292,0.25 10 false 21 4.354,1.51 5.313,1.76 0.958,0.25 10 false SGR 4.354,1 5.208,1.281 0.854,0.281 10 false SHRL 4.115,1 4.406,1.25 0.292,0.25 10 false 19 4.115,0.49 4.406,0.74 0.292,0.25 10 false 12 4.354,0.49 5.042,0.74 0.688,0.25 10 false SBR

CAUTION / NOTICE / HINT

NOTICE:
·

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

If any of the following are performed, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

-

Replacement of the rear height control sensor sub-assembly

-

Removal/installation of the rear height control sensor sub-assembly

-

Work that changes the vehicle height such as replacement of suspension components




PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.


e.

Clear the DTCs.


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.


e.

Check for DTCs.

OK:

DTC B2416 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING GTS
3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor sub-assembly power supply value 0.00 to 5.00 V 4.61 to 5.00 V -

OK:

Normal condition listed above is displayed.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
4.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
a.

Remove the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A34 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-3 (SHB) - A34-12 (SBR) Always Below 1 Ω
R1-1 (SHG) - A34-21 (SGR) Always Below 1 Ω
R1-3 (SHB) or A34-12 (SBR) - Body ground Always 10 kΩ or higher
R1-1 (SHG) or A34-21 (SGR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR