Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2019.07
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Power Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the power switch illumination.

WIRING DIAGRAM

E231352E38
3.042,0.802 3.469,0.979 0.427,0.177 10 false SWIL 4.385,0.896 4.688,1.073 0.302,0.177 10 false G79 4.729,0.885 5.094,1.063 0.365,0.177 10 false SWIL 4.427,0.719 4.688,0.896 0.26,0.177 10 false 16 4.385,1.281 4.698,1.448 0.313,0.167 10 false G79 4.729,1.271 5.167,1.448 0.438,0.177 10 false AGND 4.427,1.094 4.688,1.271 0.26,0.177 10 false 24 3.479,0.792 3.625,0.969 0.146,0.177 10 false 9 2.979,1.188 3.469,1.365 0.49,0.177 10 false AGND 1.771,1.74 2.125,1.917 0.354,0.177 10 false G96 1.781,1.906 3.813,2.083 2.031,0.177 10 false Power Switch 4.365,1.74 6.167,2.229 1.802,0.49 10 false Certification ECU (Smart Key ECU Assembly) 3.479,1.188 3.625,1.365 0.146,0.177 10 false 6

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Check that the illumination operates.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Power/Engine SW Light Power switch light OFF/ON When performing this Active Test, make sure the following condition is met:
The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.

OK:

Power switch illumination comes on.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT POWER SWITCH
2.INSPECT POWER SWITCH
a.

b.

OK:

Power switch illumination comes on.



OK

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G79 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G96-9 (SWIL) - G79-16 (SWIL) Always Below 1 Ω
G96-6 (AGND) - G79-24 (AGND) Always Below 1 Ω
G96-9 (SWIL) - Body ground Always 10 kΩ or higher
G96-6 (AGND) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR