Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2019.07
RM2170E _56 Audio / Visual / Telematics _057029 AUDIO / VIDEO _0278060 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.


for "Bluetooth":

Speed signals are received from the combination meter assembly and used to cancel "Bluetooth" function operation.

The radio receiver assembly recognizes that the vehicle is being driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E421961E01
0.198,1.26 4.385,1.469 4.188,0.208 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.25,0.417 1.542,0.563 0.292,0.146 10 false SP1 0.198,1.115 0.521,1.292 0.323,0.177 10 false A41 1.615,0.417 1.802,0.563 0.188,0.146 10 false 11 0.229,2.615 2.052,3 1.823,0.385 10 false Certification ECU (Smart Key ECU Assembly) 0.229,2.438 0.844,2.604 0.615,0.167 10 false G79 1.375,2.198 1.719,2.354 0.344,0.156 10 false SPD 1.75,2.198 1.927,2.354 0.177,0.156 10 false 27 2.885,2.083 3.063,2.24 0.177,0.156 10 false 37 4,2.083 4.177,2.24 0.177,0.156 10 false 15 4,3.5 4.177,3.656 0.177,0.156 10 false 16 2.865,2.292 3.198,2.448 0.333,0.156 10 false 3A 4,2.292 4.333,2.448 0.333,0.156 10 false 3B 4,3.698 4.333,3.854 0.333,0.156 10 false 3A 5.365,0.427 5.667,0.573 0.302,0.146 10 false 40 5.365,2.188 5.635,2.333 0.271,0.146 10 false 39 5.635,0.521 5.833,0.667 0.198,0.146 10 false SI 5.625,2.302 5.823,2.448 0.198,0.146 10 false +S 5.208,2.521 5.479,2.667 0.271,0.146 10 false G1 5.208,2.667 7.042,2.969 1.833,0.302 10 false Combination Meter Assembly 5.615,3.594 5.938,3.74 0.323,0.146 10 false SPD 5.365,3.594 5.677,3.76 0.313,0.167 10 false 17 5.198,3.854 5.531,4.01 0.333,0.156 10 false G41 5.198,4.01 6.948,4.188 1.75,0.177 10 false Radio Receiver Assembly* 2.938,4.365 4.156,4.531 1.219,0.167 10 false Junction Connector 4.573,4.771 6.906,4.948 2.333,0.177 10 false *: w/ Audio and Visual System

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U183364E02
0.615,2.083 0.875,1.417 false 0.896,3.875 1.344,3.875 false 0.802,3.708 0.802,4.031 false 1.448,3.708 1.448,4.031 false 0.188,0.167 0.344,0.323 0.156,0.156 10 false *a 0.49,2.094 0.677,2.25 0.188,0.156 10 false +S 2.76,3.656 3.083,3.813 0.323,0.156 10 false GND 1.031,3.927 1.25,4.115 0.219,0.188 10 false (A) 1.625,0.563 1.865,0.719 0.24,0.156 10 false G1

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G1-39 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G1-39 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the radio receiver assembly and combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-17 (SPD) - G1-39 (+S) Always Below 1 Ω




OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the radio receiver assembly connector and junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-17 (SPD) - 3A-16 Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - JUNCTION CONNECTOR)