Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).

DTC No. DTC Detection Condition Trouble Area
B2430 LED headlight LH circuit malfunction
·

Headlight LED unit assembly LH

·

Headlight unit assembly LH

·

H-LP Relay

·

Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


B2431 LED headlight RH circuit malfunction
·

Headlight LED unit assembly RH

·

Headlight unit assembly RH

·

H-LP Relay

·

Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



NOTICE:

DTC B2430 and B2431 are not stored until 20 seconds have elapsed after turning the power switch on (READY).


WIRING DIAGRAM

E441592E03
0.302,0.865 1.167,1.24 0.865,0.375 10 false from Auxiliary Battery 3.208,1.542 3.813,1.729 0.604,0.188 10 false H-LP 2.875,0.76 3.031,0.958 0.156,0.198 10 false 1 3.698,0.771 3.854,0.969 0.156,0.198 10 false 2 2.875,1.146 3.031,1.344 0.156,0.198 10 false 5 3.708,1.146 3.865,1.344 0.156,0.198 10 false 3 4.417,0.677 4.729,0.875 0.313,0.198 10 false 18 4.427,0.885 4.74,1.083 0.313,0.198 10 false 3C 5.771,0.677 6.083,0.875 0.313,0.198 10 false 15 6.156,0.885 6.771,1.083 0.615,0.198 10 false HRLY 4.458,1.229 6.052,1.771 1.594,0.542 10 false Instrument Panel Junction Block Assembly 2.948,2.604 3.948,2.833 1,0.229 10 false H-LP LH-LO 1.698,2.646 1.854,2.844 0.156,0.198 10 false E 2.344,2.469 2.656,2.667 0.313,0.198 10 false LO 2.635,2.344 2.792,2.542 0.156,0.198 10 false 4 1.49,3.125 1.948,3.323 0.458,0.198 10 false A69 1.49,3.281 3.479,3.479 1.99,0.198 10 false Headlight Assembly LH 2.635,4.177 2.802,4.365 0.167,0.188 10 false 1 1.708,4.083 1.865,4.281 0.156,0.198 10 false E 2.354,3.938 2.667,4.135 0.313,0.198 10 false LO 1.49,3.979 1.646,4.177 0.156,0.198 10 false 2 2.969,4.083 3.969,4.313 1,0.229 10 false H-LP RH-LO 1.51,4.563 1.969,4.76 0.458,0.198 10 false A68 1.5,4.729 3.49,4.927 1.99,0.198 10 false Headlight Assembly RH 5.74,4.271 6.052,4.469 0.313,0.198 10 false G60 5.438,4.844 7.073,5.26 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 5.781,0.885 6.094,1.083 0.313,0.198 10 false MB 5.75,2.823 6.063,3.021 0.313,0.198 10 false G60 5.792,2.615 6.104,2.813 0.313,0.198 10 false 24 5.792,4.083 6.104,4.281 0.313,0.198 10 false 21 2.635,2.708 2.792,2.906 0.156,0.198 10 false 1 1.49,2.51 1.646,2.708 0.156,0.198 10 false 2 2.635,3.823 2.792,4.021 0.156,0.198 10 false 4 2.417,2.823 2.573,3.021 0.156,0.198 10 false S 2.427,4.281 2.583,4.479 0.156,0.198 10 false S 6.167,2.823 6.781,3.021 0.615,0.198 10 false LLEW 6.156,4.281 6.771,4.479 0.615,0.198 10 false RLEW 1.698,1.042 2.5,1.219 0.802,0.177 10 false H-LP-MAIN

HEADLIGHT ASSEMBLY CIRCUIT


E441594E02
0.583,0.813 1.198,1.01 0.615,0.198 10 false LO 2.167,1.177 2.354,1.354 0.188,0.177 10 false 6 2.823,1.896 4.073,2.135 1.25,0.24 10 false Light Control ECU 3.406,2.74 3.563,2.938 0.156,0.198 10 false B 2.854,3.198 5.917,3.396 3.063,0.198 10 false Headlight Unit Assembly 3.594,2.74 5.594,2.948 2,0.208 10 false Headlight LED Unit Assembly 5.083,1.281 6.167,1.479 1.083,0.198 10 false Low Beam 0.594,1.188 1.208,1.385 0.615,0.198 10 false S 0.594,1.552 1.208,1.75 0.615,0.198 10 false E 2.167,0.813 2.563,1.031 0.396,0.219 10 false 1 2.177,1.542 2.365,1.719 0.188,0.177 10 false 3


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See pageVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Both DTC B2430 and B2431 are not output. A
Both DTC B2430 and B2431 are output. B
DTC B2430 or B2431 is output. C


NOTICE:

DTC B2430 and B2431 are not stored until 20 seconds have elapsed after turning the power switch on (READY).




A

B

2.INSPECT H-LP RELAY

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
2.INSPECT H-LP RELAY
a.
E209495

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connector Condition Specified Condition
Relay terminal 1 - Body ground Power switch off 11 to 14 V
Relay terminal 5 - Body ground Power switch off 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the A69 headlight assembly LH connector.


b.

Disconnect the A68 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - A69-4 (LO) Always Below 1 Ω
Relay terminal 3 - A68-4 (LO) Always Below 1 Ω
Relay terminal 3 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - 3C-18 Always Below 1 Ω
Relay terminal 2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U159634E02
1.594,3.49 1.594,3.75 false 0.167,0.156 0.365,0.344 0.198,0.188 10 false *a 1.625,0.823 1.833,0.979 0.208,0.156 10 false 3C 1.594,2.99 1.896,3.167 0.302,0.177 10 false MB 1.365,3.76 1.75,3.906 0.385,0.146 10 false HRLY

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
a.

Disconnect the A69 headlight assembly connector or the A68 headlight assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A69-4 (LO) - Body ground Power switch off, light control switch in head position 11 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A68-4 (LO) - Body ground Power switch off, light control switch in head position 11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
A69-2 (E) - Body ground Always Below 1 Ω

RH Side (B2431)
Tester Connection Condition Specified Condition
A68-2 (E) - Body ground Always Below 1 Ω




OK

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A69-1 (S) - Body ground Power switch on (IG) 9.5 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A68-1 (S) - Body ground Power switch on (IG) 9.5 to 14 V




OK

10.CHECK FOR DTC

NG

19.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU - HEADLIGHT ASSEMBLY)
10.CHECK FOR DTC
a.

Connect all of the disconnected connectors.


b.

Check for DTCs (See pageVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B2430 is output. A
DTC B2431 is output. B


NOTICE:

DTC B2430 and B2431 are not stored until 20 seconds have elapsed after turning the power switch on (READY).




A

11.CHECK HEADLIGHT UNIT ASSEMBLY LH

B

15.CHECK HEADLIGHT UNIT ASSEMBLY RH
11.CHECK HEADLIGHT UNIT ASSEMBLY LH
a.

Interchange the headlight unit assembly LH with RH and connect the connectors (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY).



NEXT

12.CLEAR DTC
12.CLEAR DTC

NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs (See pageVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B2430 is output. A
DTC B2431 is output. B


NOTICE:

DTC B2430 and B2431 are not stored until 20 seconds have elapsed after turning the power switch on (READY).




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

14.INSPECT HEADLIGHT UNIT ASSEMBLY LH

C

14.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E441071C05
1.938,0.625 2.25,0.896 0.313,0.271 4.74,0.635 5.177,0.896 0.438,0.26 5.375,1.344 5.76,1.188 false 5.458,0.917 5.125,1.333 false 4.177,1.188 4.563,1.344 false 2.063,0.688 2.219,0.885 0.156,0.198 10 false B 4.844,0.688 5.115,0.865 0.271,0.177 10 false A69 1.354,0.646 1.594,0.844 0.24,0.198 10 false *a 4.031,0.635 4.271,0.833 0.24,0.198 10 false *b 5.802,1.083 6.073,1.26 0.271,0.177 10 false S 3.958,1.073 4.219,1.24 0.26,0.167 10 false LO 5.5,0.771 5.76,0.938 0.26,0.167 10 false E
*a Component without harness connected
(to Headlight LED Unit Assembly LH)
*b Component without harness connected
(to Wire Harness)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - A69-4 (LO) Always Below 1 Ω
B-6 - A69-1 (S) Always Below 1 Ω
B-3 - A69-2 (E) Always Below 1 Ω




OK

NG

15.CHECK HEADLIGHT UNIT ASSEMBLY RH
a.

Interchange the headlight unit assembly RH with LH and connect the connectors (See pageVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>DISASSEMBLY).



NEXT

16.CLEAR DTC
16.CLEAR DTC

NEXT

17.CHECK FOR DTC
17.CHECK FOR DTC
a.

Check for DTCs (See pageVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B2431 is output. A
DTC B2430 is output. B


NOTICE:

DTC B2430 and B2431 are not stored until 20 seconds have elapsed after turning the power switch on (READY).




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

18.INSPECT HEADLIGHT UNIT ASSEMBLY RH

C

18.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E441071C06
1.938,0.625 2.25,0.896 0.313,0.271 4.74,0.635 5.177,0.896 0.438,0.26 5.375,1.344 5.76,1.188 false 5.458,0.917 5.125,1.333 false 4.177,1.188 4.563,1.344 false 2.052,0.688 2.208,0.885 0.156,0.198 10 false B 4.844,0.688 5.115,0.865 0.271,0.177 10 false A68 1.354,0.646 1.594,0.844 0.24,0.198 10 false *a 4.031,0.635 4.271,0.833 0.24,0.198 10 false *b 5.813,1.083 6.083,1.26 0.271,0.177 10 false S 3.948,1.073 4.208,1.24 0.26,0.167 10 false LO 5.5,0.771 5.76,0.938 0.26,0.167 10 false E
*a Component without harness connected
(to Headlight LED Unit Assembly RH)
*b Component without harness connected
(to Wire Harness)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - A68-4 (LO) Always Below 1 Ω
B-6 - A68-1 (S) Always Below 1 Ω
B-3 - A68-2 (E) Always Below 1 Ω




OK

NG

19.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU - HEADLIGHT ASSEMBLY)
a.

Disconnect the G60 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
G60-24 (LLEW) - A69-1 (S) Always Below 1 Ω
G60-24 (LLEW) - Body ground Always 10 kΩ or higher

RH Side (B2431)
Tester Connection Condition Specified Condition
G60-21 (RLEW) - A68-1 (S) Always Below 1 Ω
G60-21 (RLEW) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR