Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

U161628E03
5.021,2.135 5.021,1.844 false 4.198,1.094 4.313,0.677 4.313,0.677 4.448,0.677 false 1.031,2.198 1.51,1.24 false 1.021,2.573 0.948,1.792 0.948,1.792 0.865,1.729 false 0.99,2.969 0.469,3.552 false 0.99,3.323 1.521,3.698 false 4.688,2.333 4.927,2.49 false 4.635,1.438 4.917,1.646 false 5.031,1.979 5.396,2.281 false 5.531,0.25 5.635,0.25 5.635,0.25 5.875,1.458 false 3.698,1.188 3.99,1.385 0.292,0.198 10 false 4.65 5.417,2.24 5.875,2.458 0.458,0.219 10 false 1.11 V 4.26,1.344 4.719,1.563 0.458,0.219 10 false VTA2 2.396,0.615 4.104,0.844 1.708,0.229 10 false Sensor Output Voltage (V) 4.51,0.604 5.75,0.833 1.24,0.229 10 false Fail-safe Angle 4.156,3.448 6.563,3.646 2.406,0.198 10 false Throttle Valve Opening Angle (°) 3.573,1.823 4.042,2.021 0.469,0.198 10 false 2.525* 3.625,2.333 4.063,2.531 0.438,0.198 10 false 0.91* 3.688,1.979 4.125,2.177 0.438,0.198 10 false 2.25 3.688,2.49 4.125,2.688 0.438,0.198 10 false 0.69 4.979,2.438 5.438,2.656 0.458,0.219 10 false VTA1 4.729,3.198 5.875,3.396 1.146,0.198 10 false Usable Range 3.969,3.25 4.323,3.448 0.354,0.198 10 false 0 4.094,2.823 4.323,3.021 0.229,0.198 10 false 5.5 6.25,3.271 6.635,3.469 0.385,0.198 10 false 86 0.083,4.333 0.594,4.531 0.51,0.198 10 false Note: 0.083,4.729 3.594,5.094 3.51,0.365 10 false The throttle valve opening angle transmitted through sensor terminal VTA1 is expressed as a percentage. 0.083,5.458 3.281,5.688 3.198,0.229 10 false Between 10% and 22%: Throttle valve fully closed 0.083,5.802 3.188,6.031 3.104,0.229 10 false Between 64% and 96%: Throttle valve fully open 0.083,6.188 3.083,6.417 3,0.229 10 false Approximately 18.2%: Fail safe angle (5.5°) 1.563,1.146 2.198,1.344 0.635,0.198 10 false Magnet 0.094,4.042 1.615,4.406 1.521,0.365 10 false Throttle Position Sensor 1.552,3.625 2.063,3.823 0.51,0.198 10 false Magnet 0.333,1.656 0.969,1.875 0.635,0.219 10 false IC No. 1 0.26,3.573 0.896,3.792 0.635,0.219 10 false IC No. 2 2.385,4.042 2.896,4.24 0.51,0.198 10 false ECM 1.677,1.969 2.083,2.188 0.406,0.219 10 false VCTA 1.771,3.083 2.125,3.302 0.354,0.219 10 false ETA 1.708,2.354 2.167,2.573 0.458,0.219 10 false VTA1 1.708,2.708 2.167,2.927 0.458,0.219 10 false VTA2 4.031,3.854 5.625,4.052 1.594,0.198 10 false *: During fail-safe control 3.75,5.563 7,5.74 3.25,0.177 10 false VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V 3.75,5.156 5.958,5.354 2.208,0.198 10 false Characteristics of sensor output: 3.896,0.167 5.583,0.375 1.688,0.208 10 false Line indicating VTA2 x 0.8 3.771,0.99 3.979,1.188 0.208,0.198 10 false 5.0

DTC No. DTC Detection Condition Trouble Area
P0120 The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

ECM


P0121 The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

Throttle position sensor circuit

·

ECM


P0122 The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

Short in VTA1 circuit

·

Open in VCTA circuit

·

ECM


P0123 The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA1 circuits

·

ECM


P0220 The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

ECM


P0222 The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

Short in VTA2 circuit

·

Open in VCTA circuit

·

ECM


P0223 The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA2 circuits

·

ECM


P2135 Either of the following conditions is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body assembly)

·

ECM



MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135:
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.


P0121:

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. The ECM illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A377015E11
2.656,2 2.385,1.292 2.385,1.292 2.625,1.292 false 3.708,1.365 3.333,0.427 3.333,0.427 3.552,0.427 false 4.958,2 5.396,1.052 5.396,1.052 5.594,1.052 false 1.24,1.885 1.708,2.208 0.469,0.323 10 false Idling 0.313,2.146 2.167,2.635 1.854,0.49 10 false Power Switch on (IG) 2.125,2.031 2.594,2.354 0.469,0.323 10 false [A] 2.688,1.208 3.563,1.531 0.875,0.323 10 false Released 3.875,1.792 4.344,2.115 0.469,0.323 10 false [B] 4.729,1.781 5.198,2.104 0.469,0.323 10 false [C] 4.375,2.625 5.021,3.031 0.646,0.406 10 false 2 seconds or more 5.021,2.979 5.49,3.302 0.469,0.323 10 false [D] 3.625,0.333 4.708,0.646 1.083,0.313 10 false Depressed 5.635,0.948 6.51,1.271 0.875,0.323 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

9.

Idle the engine for 2 seconds or more [C].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions, are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM stops the engine and the vehicle can be driven using solely the hybrid system. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the power switch is then turned off.

WIRING DIAGRAM

A259011E01
0.43,2.852 0.633,3.017 0.202,0.165 10 D4 0.424,3.011 2.315,3.379 1.891,0.369 10 Throttle Position Sensor (Built into Throttle Body Assembly) 1.1,0.658 1.274,0.823 0.174,0.165 10 IC 1.1,1.547 1.274,1.712 0.174,0.165 10 IC 1.638,0.464 1.933,0.625 0.295,0.161 10 VTA 1.708,1.027 1.938,1.183 0.230,0.156 10 VC 1.558,1.572 1.946,1.755 0.387,0.184 10 VTA2 1.722,2.144 1.941,2.307 0.219,0.163 10 E2 5.583,0.466 5.962,0.627 0.379,0.161 10 VTA1 5.583,1.029 5.985,1.185 0.402,0.156 10 VCTA 5.583,1.574 5.971,1.758 0.387,0.184 10 VTA2 5.583,2.147 5.890,2.310 0.307,0.163 10 ETA 1.993,0.462 2.103,0.618 0.110,0.156 10 6 1.993,1.003 2.094,1.178 0.100,0.174 10 5 1.984,1.555 2.094,1.747 0.110,0.193 10 4 1.982,2.124 2.095,2.290 0.113,0.167 10 3 5.831,2.858 6.107,3.050 0.276,0.193 10 D28 5.318,0.455 5.515,0.616 0.198,0.161 10 90 5.318,1.015 5.515,1.176 0.198,0.161 10 88 5.318,1.548 5.515,1.708 0.198,0.161 10 89 5.29,2.141 5.567,2.301 0.277,0.161 10 111 6.167,2.858 6.504,3.013 0.336,0.156 10 ECM 3.856,1.976 4.054,2.137 0.198,0.161 10 * 3.856,0.715 4.054,0.876 0.198,0.161 10 * 4.085,3.274 4.902,3.430 0.817,0.156 10 *: Shielded

CAUTION / NOTICE / HINT

HINT:
·

DTC P0121 is stored when the voltages output from VTA1 and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

Characteristic of sensor output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No. 1

VTA2: Throttle position No. 2


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D4-5 (VC) - D28-88 (VCTA) Always Below 1 Ω
D4-6 (VTA) - D28-90 (VTA1) Always Below 1 Ω
D4-4 (VTA2) - D28-89 (VTA2) Always Below 1 Ω
D4-3 (E2) - D28-111 (ETA) Always Below 1 Ω
D4-5 (VC) or D28-88 (VCTA) - Body ground Always 10 kΩ or higher
D4-6 (VTA) or D28-90 (VTA1) - Body ground Always 10 kΩ or higher
D4-4 (VTA2) or D28-89 (VTA2) - Body ground Always 10 kΩ or higher




OK

2.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (VC VOLTAGE)
a.
U110408E02
1.427,3.031 1.604,2.49 false 2.156,3.042 2.01,2.49 false 0.167,0.198 0.375,0.385 0.208,0.188 10 false *a 1.313,3.052 1.729,3.313 0.417,0.26 10 false E2 2.063,3.052 2.479,3.302 0.417,0.25 10 false VC 0.427,2.25 0.75,2.417 0.323,0.167 10 false D4

Disconnect the throttle body assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D4-5 (VC) - D4-3 (E2) Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Throttle Body Assembly)



OK

3.REPLACE THROTTLE BODY ASSEMBLY

NG

3.REPLACE THROTTLE BODY ASSEMBLY
a.

Replace the throttle body assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
4.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output A
DTC is not output B



A

B

END