Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0505  Idle Control System Malfunction  


DESCRIPTION

The idle speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) the one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idle speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No. DTC Detection Condition Trouble Area
P0505 Idle speed continues to vary greatly from the target idle speed (2 trip detection logic).
·

Electronic throttle control system

·

Intake system

·

PCV hose connections

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

The ECM monitors the idle speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if either of the following conditions is met:

·

After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the difference between the target and actual engine idle speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the IAC flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.

A398183E01
2.302,1.844 3.417,2.083 1.115,0.24 10 false Target Speed 2.302,2.885 3.573,3.135 1.271,0.25 10 false Actual Idle Speed 0.729,0.958 1.844,1.198 1.115,0.24 10 false Idle Speed 3.958,0.917 5.531,1.156 1.573,0.24 10 false Learned Idle Air Volume 4.302,1.531 5.417,1.771 1.115,0.24 10 false Large 4.563,2.333 5.677,2.573 1.115,0.24 10 false 0 4.292,3.073 5.406,3.313 1.115,0.24 10 false Small 3.26,3.5 4.375,3.74 1.115,0.24 10 false Time 6.24,1.323 7.052,1.625 0.813,0.302 10 false Maximum 6.271,2.854 7.083,3.156 0.813,0.302 10 false Minimum 6.354,3.667 6.885,3.938 0.531,0.271 10 false Time


MONITOR STRATEGY

Required Sensors/Components (Main) Electronic throttle control system
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation Once per driving cycle
MIL Operation 2 driving cycles

TYPICAL MALFUNCTION THRESHOLDS

Both of following conditions A and B met -
A. Frequency that both of following conditions (a) and (b) met 5 times or more
(a) Engine speed - Target engine speed Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
(b) Vehicle condition Stopped after being driven at 10 km/h (6.25 mph) or more
B. Either conditions is met (c) or (d)
(c) IAC flow rate learned value Lower limit or upper limit
(d) Amount of change of IAC flow rate learned value exceeds threshold

CONFIRMATION DRIVING PATTERN

A249361E10
1.917,2.792 1.24,3.198 1.24,3.198 1.24,3.281 false 2.698,2.792 2.698,3.031 2.698,3.031 3.563,3.031 false 3.302,2.792 3.302,3.021 false 3.01,0.958 3.188,0.323 3.188,0.323 3.354,0.323 false 0.271,1.177 1.427,1.5 1.156,0.323 10 false 10 km/h or more 0.958,1.854 1.5,2.083 0.542,0.229 10 false Idling 0.448,2.219 1.302,2.635 0.854,0.417 10 false Power Switch on (IG) 1.823,2.094 2.021,2.281 0.198,0.188 10 false [A] 2.292,1.281 2.563,1.51 0.271,0.229 10 false [B] 5.615,3.135 5.833,3.313 0.219,0.177 10 false [F] 3.219,1.635 3.469,1.833 0.25,0.198 10 false [E] 5.552,1.646 5.802,1.844 0.25,0.198 10 false [E] 4.938,1.635 5.188,1.833 0.25,0.198 10 false [E] 4.365,1.635 4.615,1.833 0.25,0.198 10 false [E] 3.781,1.625 4.031,1.823 0.25,0.198 10 false [E] 2.604,1.635 2.823,1.813 0.219,0.177 10 false [C] 0.385,3.313 3.479,3.479 3.094,0.167 10 false Engine coolant temperature is 25°C or less 4.677,0.26 4.896,0.438 0.219,0.177 10 false [D] 3.51,0.823 3.729,1 0.219,0.177 10 false [D] 4.083,0.823 4.302,1 0.219,0.177 10 false [D] 4.667,0.823 4.885,1 0.219,0.177 10 false [D] 5.24,0.823 5.458,1 0.219,0.177 10 false [D] 3.615,2.948 4.844,3.115 1.229,0.167 10 false 5 seconds or more 3.406,0.25 4.698,0.417 1.292,0.167 10 false 10 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

4.

Make sure that the coolant temperature is 25°C (77°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the power switch off and wait for at least 30 seconds.

7.

Turn the power switch on (IG) and turn the GTS on [A].

8.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

9.

Start the engine and drive the vehicle until the coolant temperature reaches 70°C (158°F) [B].

HINT:

If the coolant temperature is 40°C (104°F) or higher, the engine may stop when idling.


10.

Stop the vehicle (0 km/h (0 mph)) for 5 seconds or more [C].

11.

Accelerate the vehicle to 10 km/h (6.25 mph) or more for 10 seconds or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

When accelerating the vehicle, depress the accelerator pedal more than normal to start the engine.


·

The engine may stop during acceleration. However, this will not affect the confirmation driving.



12.

Stop the vehicle (0 km/h (0 mph)) for 5 seconds or more [E].

13.

Repeat steps [D] and [E] for 5 times or more.

14.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

17.

Input the DTC: P0505.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The following conditions may also cause DTC P0505 to be stored:

(a)

The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.

(b)

The accelerator pedal being not fully released.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Engine Speed and ISC Learning Value] (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0505 is output A
DTC P0505 and other DTCs are output B

HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>2ZR-FXE (EMISSION CONTROL)>PCV VALVE>COMPONENTS).

OK:

PCV valve and hose are connected correctly and are not damaged.




OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks from the intake system.




OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

5.INSPECT EGR VALVE ASSEMBLY

B

6.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE VALVE)
5.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

6.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE VALVE)

NG

6.INSPECT THROTTLE BODY ASSEMBLY (THROTTLE VALVE)
a.

Check the throttle body assembly condition.

OK:

Throttle valve is not contaminated with foreign matter and moves smoothly.




OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0505)

NG

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0505)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC P0505 is output A
DTC is not output B



A

B

END