Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should illuminate and should then turn off after power switch is turned on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A259027E09
6.208,4.094 6.51,4.25 0.302,0.156 10 false A57 6.49,4.094 6.844,4.271 0.354,0.177 10 false ECM 6.063,0.875 6.271,1.083 0.208,0.208 10 false W 3.927,1.458 4.219,1.635 0.292,0.177 10 false L27 3.927,1.615 5.125,2.021 1.198,0.406 10 false Combination Meter Sub-assembly 3.469,1.115 3.792,1.281 0.323,0.167 10 false MET 0.76,1.104 1.021,1.271 0.26,0.167 10 false IG2 0.365,2.667 0.698,2.844 0.333,0.177 10 false P/I 1 0.365,3.125 0.75,3.323 0.385,0.198 10 false MAIN 0.479,3.833 1.042,4.219 0.563,0.385 10 false Auxiliary Battery 1.563,3.865 2.073,4.073 0.51,0.208 10 false L195 1.552,4.01 3.083,4.469 1.531,0.458 10 false Certification ECU (Smart Key ECU Assembly) 1.917,3.385 2.302,3.542 0.385,0.156 10 false IG2D 2.313,3.281 2.5,3.469 0.188,0.188 10 false 9 1.646,1.646 1.896,1.802 0.25,0.156 10 false IG2 5.813,0.875 6,1.031 0.188,0.156 10 false 36 2.958,0.792 3.125,0.958 0.167,0.167 10 false 4 2.896,0.979 3.094,1.146 0.198,0.167 10 false 1A 2.74,2.281 2.938,2.448 0.198,0.167 10 false 1A 0.979,2.281 1.177,2.448 0.198,0.167 10 false 1A 0.198,2.281 0.396,2.448 0.198,0.167 10 false 1C 2.542,2.271 2.698,2.438 0.156,0.167 10 false 2 0.479,2.271 0.635,2.438 0.156,0.167 10 false 1 1.281,2.271 1.438,2.438 0.156,0.167 10 false 3 1.271,2.469 2.729,2.656 1.458,0.188 10 false No. 2 Integration Relay 4.031,1.094 4.281,1.25 0.25,0.156 10 false IG+ 4.729,1.083 4.979,1.24 0.25,0.156 10 false EFI 3.854,0.865 4.042,1.021 0.188,0.156 10 false 2 5.01,0.865 5.198,1.021 0.188,0.156 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the power switch on (IG).


b.

Check the illumination of the MIL.

Result
Condition Proceed to
MIL remains illuminated A
MIL remains off B
MIL illuminates and should turn off after power switch is turned on (READY) C



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT ENGINE STARTS

C

2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been stored. Note down the DTCs.



g.

Check if the MIL goes off.

OK:

MIL goes off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A57 ECM connector.


b.

Turn the power switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
a.

Disconnect the combination meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-6 (EFI) or A57-36 (W) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C

5.CHECK THAT ENGINE STARTS
a.

Turn the power switch on (IG).


b.

Turn the GTS on.


c.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


d.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine cannot be put in inspection mode*
(Engine cannot start)
B


HINT:

*: The GTS cannot communicate with the ECM.




A

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-36 (W) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - ECM)
a.

Disconnect the combination meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-6 (EFI) - A57-36 (W) Always Below 1 Ω


Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE COMBINATION METER SUB-ASSEMBLY

C