Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM J

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly uses 5 V from the auxiliary battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A259023E11
1.344,0.833 2.656,1.125 1.313,0.292 10 false from EFI MAIN Fuse 1.333,1.188 2.698,1.49 1.365,0.302 10 false from EFI MAIN Relay 0.625,2.042 2.573,2.375 1.948,0.333 10 false to Throttle Position Sensor, etc. (Sensors which have an IC) 0.146,2.698 2.573,3.094 2.427,0.396 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.063 5.313,3.375 0.344,0.313 10 false ECM 2.885,0.729 3.271,0.875 0.385,0.146 10 false BATT 2.823,1.083 3.406,1.302 0.583,0.219 10 false +B, +B2 2.74,1.792 3.677,2.125 0.938,0.333 10 false VCTA, VCV1, VCPM 4.375,0.927 6.167,1.281 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.375,1.865 6.365,2.219 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit is shorted, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the power switch is turned on (IG). The MIL goes off when the power switch is turned on (READY).


WIRING DIAGRAM

A261346E06
2.448,0.344 2.542,0.5 0.094,0.156 10 false 5 2.156,0.427 2.438,0.615 0.281,0.188 10 false VC 2.448,0.708 2.542,0.865 0.094,0.156 10 false 3 2.177,0.792 2.385,1 0.208,0.208 10 false E2 2.448,1.073 2.542,1.229 0.094,0.156 10 false 6 2.073,1.156 2.385,1.344 0.313,0.188 10 false VTA 2.448,1.438 2.542,1.594 0.094,0.156 10 false 4 5.24,0.344 5.49,0.5 0.25,0.156 10 false 88 5.167,0.698 5.417,0.854 0.25,0.156 10 false 111 5.24,1.073 5.49,1.229 0.25,0.156 10 false 90 5.24,1.438 5.49,1.594 0.25,0.156 10 false 89 5.5,0.344 5.885,0.5 0.385,0.156 10 false VCTA 5.5,0.698 5.792,0.854 0.292,0.156 10 false ETA 5.5,1.156 5.865,1.313 0.365,0.156 10 false VTA1 5.5,1.521 5.865,1.677 0.365,0.156 10 false VTA2 1.99,1.51 2.396,1.688 0.406,0.177 10 false VTA2 0.729,1.823 1,1.979 0.271,0.156 10 false D4 0.729,1.99 2.583,2.24 1.854,0.25 10 false Throttle Body Assembly 2.448,2.656 2.542,2.813 0.094,0.156 10 false 3 2.146,2.74 2.365,2.896 0.219,0.156 10 false VC 2.448,3.021 2.542,3.177 0.094,0.156 10 false 1 2.042,3.104 2.375,3.292 0.333,0.188 10 false VVI+ 2.448,3.385 2.542,3.542 0.094,0.156 10 false 2 5.229,2.646 5.479,2.802 0.25,0.156 10 false 99 5.24,3.01 5.49,3.167 0.25,0.156 10 false 76 5.167,3.375 5.5,3.635 0.333,0.26 10 false 122 5.5,2.646 5.885,2.802 0.385,0.156 10 false VCV1 5.5,3.01 5.833,3.167 0.333,0.156 10 false G2+ 5.5,3.458 5.865,3.615 0.365,0.156 10 false G2- 2.052,3.469 2.375,3.625 0.323,0.156 10 false VVI- 0.688,3.771 0.958,3.927 0.271,0.156 10 false D18 0.688,3.938 2.313,4.094 1.625,0.156 10 false Camshaft Position Sensor 2.448,4.698 2.542,4.854 0.094,0.156 10 false 3 2.146,4.792 2.365,4.948 0.219,0.156 10 false VC 2.448,5.063 2.542,5.219 0.094,0.156 10 false 2 2.177,5.156 2.365,5.313 0.188,0.156 10 false E2 2.448,5.427 2.542,5.583 0.094,0.156 10 false 1 5.24,4.688 5.417,4.844 0.177,0.156 10 false 72 5.24,5.063 5.417,5.219 0.177,0.156 10 false 71 5.24,5.417 5.417,5.573 0.177,0.156 10 false 69 5.5,4.688 5.979,4.865 0.479,0.177 10 false VCPM 5.5,5.052 5.948,5.25 0.448,0.198 10 false EPIM 5.5,5.51 5.875,5.719 0.375,0.208 10 false PIM 2.094,5.521 2.365,5.677 0.271,0.156 10 false PIM 0.438,5.813 0.708,5.969 0.271,0.156 10 false D3 0.438,5.979 2.719,6.198 2.281,0.219 10 false Manifold Absolute Pressure Sensor 5.771,6.229 6.094,6.396 0.323,0.167 10 false D28 6.104,6.229 6.427,6.385 0.323,0.156 10 false ECM

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the power switch on (IG).

OK:

MIL lights up.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

4.CHECK MIL (CAMSHAFT POSITION SENSOR)

B

4.CHECK MIL (CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

5.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.

Result
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

6.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the camshaft position sensor connector.


c.

Disconnect the manifold absolute pressure sensor connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D4-5 (VC) or D28-88 (VCTA) - Body ground Always 10 kΩ or higher
D18-3 (VC) or D28-99 (VCV1) - Body ground Always 10 kΩ or higher
D3-3 (VC) or D28-72 (VCPM) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR