Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air by applying a specific electrical current to the wire.

The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant temperature value of the hot wire, current is applied to these components in the mass air flow meter sub-assembly. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A202104E40
1.521,0.323 2.031,1.417 false 2.521,0.99 2.177,1.417 false 4.844,1.313 4.177,2.104 false 5.104,1.552 5.406,2.104 false 0.219,0.229 1.479,0.656 1.26,0.427 10 false Temperature Sensor (Thermistor) 2.26,0.229 2.542,0.448 0.281,0.219 10 false +B 2.229,0.542 3.594,0.781 1.365,0.24 10 false Power Transistor 2.563,0.865 4.333,1.063 1.771,0.198 10 false Platinum Hot Wire (Heater) 1.656,1.438 1.823,1.646 0.167,0.208 10 false A 2.458,1.438 2.646,1.635 0.188,0.198 10 false B 2.906,1.573 3.917,1.771 1.01,0.198 10 false Output Voltage 2.813,2.115 4.615,2.313 1.802,0.198 10 false Platinum Hot Wire (Heater) 4.854,2.125 6.969,2.333 2.115,0.208 10 false Temperature Sensor (Thermistor)

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter sub-assembly voltage below 0.2 V for 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0103 Mass air flow meter sub-assembly voltage higher than 4.9 V for 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM



HINT:

When any of these DTCs are output, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A249512E09
2.654,4.369 3.146,4.518 0.492,0.149 10 MAIN 2.942,3.357 3.606,3.506 0.663,0.149 10 EFI MAIN 4.033,4.372 4.584,4.521 0.551,0.149 10 P/I 1 0.787,4.956 1.364,5.339 0.577,0.383 10 Auxiliary Battery 1.629,1.027 2.368,1.221 0.740,0.194 10 EFI NO. 2 2.622,0.771 2.720,0.920 0.098,0.149 10 3 2.161,1.968 4.376,2.138 2.215,0.170 10 Mass Air Flow Meter Sub-assembly 1.921,1.968 2.118,2.110 0.197,0.142 10 D5 2.778,0.771 2.981,0.920 0.203,0.149 10 +B 3.842,0.866 4.066,1.015 0.224,0.149 10 VG 3.768,1.388 4.065,1.537 0.297,0.149 10 E2G 5.797,0.883 6.021,1.032 0.224,0.149 10 VG 5.797,1.413 6.094,1.562 0.297,0.149 10 E2G 5.805,2.713 6.231,2.862 0.426,0.149 10 MREL 6.224,5.401 6.567,5.550 0.343,0.149 10 ECM 4.119,0.873 4.217,1.022 0.098,0.149 10 5 4.119,1.399 4.217,1.547 0.098,0.149 10 4 5.571,2.616 5.681,2.765 0.111,0.149 10 6 5.462,0.961 5.747,1.110 0.285,0.149 10 D28 5.462,1.491 5.747,1.640 0.285,0.149 10 D28 5.466,2.786 5.735,2.934 0.269,0.149 10 A57 5.529,0.792 5.720,0.941 0.190,0.149 10 94 5.479,1.304 5.749,1.453 0.270,0.149 10 117 2.295,3.511 2.963,3.659 0.668,0.149 10 EFI MAIN 4.733,0.736 4.924,0.875 0.191,0.139 10 * 2.94,5.276 3.651,5.466 0.711,0.191 10 *: Shielded 3.617,3.22 3.898,3.417 0.281,0.198 10 1C 2.051,2.785 2.332,2.983 0.281,0.198 10 1B 2.046,3.223 2.327,3.421 0.281,0.198 10 1B 3.64,2.785 3.921,2.983 0.281,0.198 10 1B 3.671,3.043 3.841,3.250 0.170,0.207 10 1 3.689,2.619 3.861,2.777 0.172,0.158 10 2 2.096,2.617 2.199,2.770 0.104,0.152 10 3 2.101,3.045 2.205,3.190 0.104,0.145 10 4 2.186,3.773 3.760,3.949 1.575,0.176 10 No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ DTC OUTPUT (P0102 OR P0103)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
U190504E02
1.74,2.458 1.49,3.115 false 0.396,0.135 0.583,0.323 0.188,0.188 10 false *a 0.333,2.146 0.531,2.323 0.198,0.177 10 false D5 1.323,3.125 1.76,3.302 0.438,0.177 10 false +B (+)

a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D5-3 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-5 (VG) - D28-94 (VG) Always Below 1 Ω
D5-4 (E2G) - D28-117 (E2G) Always Below 1 Ω
D5-5 (VG) or D28-94 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter sub-assembly.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


vii.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.





OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-4 (E2G) - Body ground Always Below 1 Ω




OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D5-4 (E2G) - D28-117 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR