The inverter converts the high-voltage direct current of the HV battery into the alternating current for MG1 and MG2. The inverter generates heat during the conversion process. Therefore, the inverter is cooled by a special cooling system consisting of the inverter water pump assembly, the cooling fan, and a radiator. This cooling system is independent of the engine cooling system. The power management control ECU monitors the electric water pump, cooling fan, and cooling system, and detects the following malfunctions.
| *1 | Inverter Water Pump Assembly | *2 | Inverter Reserve Tank Assembly |
| *3 | Inverter with Converter Assembly | *4 | Radiator Assembly (HV) |
| *5 | Hybrid Vehicle Transaxle Assembly | - | - |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A93 | 346 | HV cooling temperature increases and the temperature of any inverter with converter assembly related parts increases.
(1 trip detection logic) |
·
Inverter cooling system ·
Inverter water pump assembly ·
Inverter with converter assembly ·
Cooling fan system |
| DTC No. | INF Code | Data List Item |
|---|---|---|
| P0A93 | 346 | ·
Inverter Coolant Water Temperature ·
Inverter Temp-(MG1) ·
Inverter Temp-(MG2) ·
DC/DC Cnv Temp (Upper) ·
DC/DC Cnv Temp (Lower) ·
Inverter W/P Revolution |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform a road test according to the freeze frame data "Vehicle Spd" for approximately 15 minutes.
During the road test, check Data List items "Inverter Coolant Water Temperature", "Inverter Temp-(MG2)", "Inverter Temp- (MG1)", "DC/DC Cnv Temp (Upper)" and " DC/DC Cnv Temp (Lower)" to prevent them from overheating.
Make sure that the front side of the radiator grille is not blocked with anything.
Ask the customer if the front side of the radiator grille was blocked with anything.
| Result | Proceed to |
|---|---|
| Not blocked. | A |
| Is/was blocked. | B |
If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTC P0A93-346 only is output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A02-719 | Motor Electronics Coolant Temperature Sensor Circuit Low |
| P0A03-720 | Motor Electronics Coolant Temperature Sensor Circuit High |
| P0C73-776 | Motor Electronics Coolant Pump "A" Control Performance |
| P314A-828 | Inverter Coolant Pump Speed Signal |
P0A93-346 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
OK
NG
A
B
C
OK
NG
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
Be sure that the coolant level is above the low line of the inverter reserve tank assembly.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Select Inverter W/P Revolution in the Data List.
While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.
| Tester Display | Switch Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 2250 to 5625 rpm |
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
Turn the power switch off.
OK
NG
Turn the power switch off and leave the vehicle for at least 1 hour.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Coolant Water Temperature, Inverter Temp (MG2), Cnv Tmp (Upper), Cnv Temp (Lower), Inverter Temp (MG1).
Read the Data List.
| Result | Proceed to |
|---|---|
| Other than below. | A |
| "Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (36°F) or more. | B |
The lower limit temperature that can be displayed for "Inverter Temp (MG1)", "Inverter Temp (MG2)", "Cnv Tmp (Upper)" and "Cnv Temp (Lower)" is 15°C (59°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.
Turn the power switch off.
A
B
A
B
NEXT
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG