Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C73-776  Motor Electronics Coolant Pump "A" Control Performance  


DESCRIPTION

The inverter water pump assembly transmits rotation revolution information to the power management control ECU. The power management control ECU monitors the revolution and detects malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0C73 776 A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low) or an intermittent stop malfunction (operation stops intermittently when the revolution speed is abnormal) occurs in the inverter water pump assembly.
·

Inverter cooling system

·

Wire harness or connector

·

Inverter water pump assembly

·

Power management control ECU



HINT:

The inverter water pump assembly operates when the power switch is on (READY).


Related Data List
DTC No. INF Code Data List Item
P0C73 776
·

W/P Run Control Duty*1

·

Inverter W/P Revolution

·

Ready Signal



*1: This Data List item is related to the inverter water pump assembly.

Related Active Test
DTC No. INF Code Active Test
P0C73 776 Activate the Water Pump*2

*2: This is an Active Test of the inverter water pump assembly.

WIRING DIAGRAM

A262628E10
0.729,2.24 2.063,2.781 1.333,0.542 10 false Engine Room Relay Block and Junction Block Assembly 1.583,1.76 2.198,1.948 0.615,0.188 10 false IGCT 2.198,1.177 2.948,1.365 0.75,0.188 10 false IGCT NO. 3 5.479,1.021 5.823,1.188 0.344,0.167 10 false IWP 4.354,0.99 4.698,1.156 0.344,0.167 10 false SWP 4.333,1.448 4.688,1.615 0.354,0.167 10 false NWP 3.625,1.448 3.969,1.615 0.344,0.167 10 false GND 3.625,1.021 4.042,1.188 0.417,0.167 10 false +BWP 5.479,1.469 5.927,1.635 0.448,0.167 10 false NIWP 5.479,2.99 5.927,3.156 0.448,0.167 10 false MREL 5.104,1.01 5.375,1.188 0.271,0.177 10 false A21 5.094,1.448 5.365,1.625 0.271,0.177 10 false A21 5.104,2.99 5.375,3.167 0.271,0.177 10 false A22 5.156,0.813 5.354,0.99 0.198,0.177 10 false 13 5.146,1.25 5.344,1.427 0.198,0.177 10 false 14 5.177,2.781 5.313,2.958 0.135,0.177 10 false 6 5.344,3.938 6.573,4.438 1.229,0.5 10 false Power Management Control ECU 4.75,0.896 4.885,1.073 0.135,0.177 10 false 3 4.75,1.354 4.885,1.531 0.135,0.177 10 false 2 3.458,0.917 3.594,1.094 0.135,0.177 10 false 4 2.771,0.917 2.906,1.094 0.135,0.177 10 false 2 2.385,0.927 2.521,1.104 0.135,0.177 10 false 1 2.135,0.927 2.271,1.104 0.135,0.177 10 false 5 2.135,1.344 2.271,1.521 0.135,0.177 10 false 1 1.354,0.927 1.49,1.104 0.135,0.177 10 false 3 1.354,1.333 1.49,1.51 0.135,0.177 10 false 2 3.458,1.333 3.594,1.51 0.135,0.177 10 false 1 3.625,1.948 4.729,2.323 1.104,0.375 10 false Inverter Water Pump Assembly 3.625,1.75 3.938,1.958 0.313,0.208 10 false g1 0.5,3.688 3.438,3.99 2.938,0.302 10 false IWP: Inverter water pump assembly drive duty 0.5,4 3.708,4.302 3.208,0.302 10 false NIWP: Inverter water pump assembly speed signal 0.042,0.969 0.677,1.406 0.635,0.438 10 false from IGCT Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

In the case of a coolant leak, the inverter water pump assembly activates a fail-safe function. If the inverter water pump assembly is not the cause of the coolant leak, it is not necessary to replace it.

·

If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTC. (When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)

·

If air enters the system while bleeding air during coolant exchange, etc. and the inverter water pump assembly revolution speed becomes abnormally high, the inverter water pump assembly may suspend control as a fail-safe function and the hybrid vehicle control ECU may store this DTC. (When air bleeding is complete, the inverter water pump assembly will resume normal operation. In this case, it is not necessary to replace the inverter water pump assembly.)



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 2 minutes or more.



PROCEDURE

1.CHECK QUANTITY OF HV COOLANT

A

2.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR COOLANT LEAK

2.CHECK COOLANT HOSE

OK

3.CHECK INVERTER WATER PUMP ASSEMBLY

NG

CORRECT THE PROBLEM

3.CHECK INVERTER WATER PUMP ASSEMBLY
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:
·

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.

·

When the inverter water pump assembly operation command line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.



a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List.


d.

Select Inverter W/P Revolution in the Data List.


e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 625 rpm or less


HINT:

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.



f.

Turn the power switch off.



OK

4.CLEAR DTC

NG

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
4.CLEAR DTC

NEXT

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.


d.

Select Inverter W/P Revolution in the Data List.


e.

While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.

Result:
Tester Display Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 2250 to 5625 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.




f.

Turn the power switch off.



OK

6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

NG

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
6.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

A

B

REPLACE HV COOLANT

7.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A248371

Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

The connector is connected securely and there are no contact pressure problems.




OK

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A21 power management control ECU connector.


b.

Disconnect the g1 inverter water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

U190711E02
1.396,1.865 1.771,2.198 false 5.323,1.552 5.271,1.927 false 1.802,2.156 2.125,2.396 0.323,0.24 10 false IWP 5.104,1.948 5.5,2.135 0.396,0.188 10 false SWP 0.417,0.229 0.615,0.417 0.198,0.188 10 false *a 4.385,0.24 4.583,0.427 0.198,0.188 10 false *b 1.854,1.771 2.125,1.938 0.271,0.167 10 false A21 6.021,1.438 6.292,1.625 0.271,0.188 10 false g1

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
g1-3 (SWP) - A21-13 (IWP) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
g1-3 (SWP) or A21-13 (IWP) - Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the A21 power management control ECU connector.


e.

Reconnect the g1 inverter water pump assembly connector.



OK

10.READ VALUE USING GTS (INVERTER W/P REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING GTS (INVERTER W/P REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.
A270315E02
0.146,0.152 0.388,0.393 0.242,0.242 10 *1 2.973,0.572 3.214,0.814 0.242,0.242 10 *2 2.329,0.96 2.951,0.679 false

Remove the IGCT No. 3 fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 IGCT No. 3 Fuse


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.


e.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Inverter W/P Revolution Power switch on (IG) 125 rpm or less



f.

Turn the power switch off.


g.

Install the IGCT No. 3 fuse.



OK

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A21 power management control ECU connector.


b.

Turn the power switch on (IG).


c.
U154235E02
0.781,2.438 1.292,2.583 false 1.833,1.396 2.094,2.094 false 0.75,3 1.021,3.167 0.271,0.167 10 false A21 1.333,2.542 1.656,2.708 0.323,0.167 10 false IWP 0.26,0.271 0.417,0.438 0.156,0.167 10 false *a 2.115,2.042 2.438,2.208 0.323,0.167 10 false E1 1.99,2.292 2.26,2.458 0.271,0.167 10 false L5

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-13 (IWP) - L5-6 (E1) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the A21 power management control ECU connector.



OK

12.CHECK POWER MANAGEMENT CONTROL ECU

NG

12.CHECK POWER MANAGEMENT CONTROL ECU
a.

Turn the power switch on (IG).


b.
U154412E02
1.823,1.698 2.188,2.365 false 0.781,1.771 1.104,2.375 false 1.958,0.99 2.24,1.156 0.281,0.167 10 false L5 0.646,0.99 0.927,1.156 0.281,0.167 10 false A21 0.177,0.188 0.448,0.354 0.271,0.167 10 false *a 2.125,2.385 2.438,2.552 0.313,0.167 10 false E1 0.979,2.396 1.292,2.563 0.313,0.167 10 false IWP

While turning the power switch on (IG), check the waveform between the power management control ECU terminals.

Item Content
Terminal A21-13 (IWP) - L5-6 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Power switch on (IG)

Text in Illustration
*a Component with Harness Connected
(Power Management Control ECU)

OK:

Waveform duty ratio is between 3% and 9%.



c.

Turn the power switch off.



OK

NG