Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AFC-150  Hybrid Battery Pack Sensor Module  


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO. INF Code DTC Detection Condition Trouble Area
P0AFC 150 Power source voltage of the battery smart unit drops during precharge.
·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A255047E08
0.313,1.156 0.688,1.375 0.375,0.219 10 false IGCT 2.302,1.635 2.875,1.854 0.573,0.219 10 false IGCT 3.771,1.24 4.531,1.458 0.76,0.219 10 false IGCT No. 2 2.052,0.906 2.198,1.104 0.146,0.198 10 false 3 2.052,1.281 2.198,1.479 0.146,0.198 10 false 2 2.792,1.271 2.938,1.469 0.146,0.198 10 false 1 2.792,0.906 2.938,1.104 0.146,0.198 10 false 5 4.385,0.917 4.531,1.115 0.146,0.198 10 false 2 3.802,0.927 3.948,1.125 0.146,0.198 10 false 1 5.5,0.896 5.646,1.094 0.146,0.198 10 false 5 5.51,3.615 5.656,3.813 0.146,0.198 10 false 4 5.708,1.042 6.281,1.26 0.573,0.219 10 false IGCT 5.146,4.146 5.938,4.375 0.792,0.229 10 false L144 5.5,3.313 5.625,3.51 0.125,0.198 10 false 3 5.49,2.969 5.635,3.167 0.146,0.198 10 false 2 5.708,3.74 6.094,3.969 0.385,0.229 10 false GND 5.708,3.417 6.094,3.646 0.385,0.229 10 false BTH- 5.708,3.073 6.094,3.302 0.385,0.229 10 false BTH+ 5.521,4.146 6.719,4.344 1.198,0.198 10 false Battery Smart Unit 2.771,3.427 3.156,3.656 0.385,0.229 10 false BTH- 2.75,3.083 3.135,3.313 0.385,0.229 10 false BTH+ 3.219,3.417 3.438,3.615 0.219,0.198 10 false L5 3.219,3.083 3.438,3.281 0.219,0.198 10 false L5 3.219,3.26 3.438,3.458 0.219,0.198 10 false 33 3.219,2.917 3.438,3.115 0.219,0.198 10 false 32 2.729,2.021 3.26,2.25 0.531,0.229 10 false MREL 3.167,2.01 3.521,2.229 0.354,0.219 10 false A22 3.25,1.854 3.469,2.052 0.219,0.198 10 false 6 2.198,3.729 3.438,4.135 1.24,0.406 10 false Power Management Control ECU 3.167,2.375 3.521,2.583 0.354,0.208 10 false A22 3.167,2.719 3.521,2.938 0.354,0.219 10 false A21 2.854,2.375 3.24,2.604 0.385,0.229 10 false +B1 2.854,2.719 3.24,2.948 0.385,0.229 10 false +B2 3.25,2.219 3.469,2.417 0.219,0.198 10 false 5 3.25,2.552 3.469,2.75 0.219,0.198 10 false 2 0.208,0.688 0.896,0.906 0.688,0.219 10 false HV BATT 5.5,0.438 5.646,0.635 0.146,0.198 10 false 1 5.708,0.531 5.927,0.75 0.219,0.219 10 false B

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0AFC-150 only is output, or DTC other than the one in the table below is also output. A
Following DTC is also output. B


DTC No. Relevant Diagnosis
P31AB-123 Hybrid Battery Cell Low Voltage

HINT:

P0AFC-150 may be output due to a malfunction which causes the DTC in the table above to be output. In this case, first troubleshoot the output DTC in the table above. Then, perform a reproduction test to check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

OK

NG

4.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (B OR IGCT CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)