Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AFC-123  Hybrid Battery Pack Sensor Module  


DESCRIPTION

If the battery smart unit detects an internal malfunction, it sends an error signal to the power management control ECU. When the power management control ECU receives the error signal from the battery smart unit, the ECU warns the driver and performs fail-safe control.


DTC No. INF Code DTC Detection Condition Trouble Area
P0AFC 123 The power management control ECU receives an error signal from the battery smart unit.
·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A255047E08
0.313,1.156 0.688,1.375 0.375,0.219 10 false IGCT 2.302,1.635 2.875,1.854 0.573,0.219 10 false IGCT 3.771,1.24 4.531,1.458 0.76,0.219 10 false IGCT No. 2 2.052,0.906 2.198,1.104 0.146,0.198 10 false 3 2.052,1.281 2.198,1.479 0.146,0.198 10 false 2 2.792,1.271 2.938,1.469 0.146,0.198 10 false 1 2.792,0.906 2.938,1.104 0.146,0.198 10 false 5 4.385,0.917 4.531,1.115 0.146,0.198 10 false 2 3.802,0.927 3.948,1.125 0.146,0.198 10 false 1 5.5,0.896 5.646,1.094 0.146,0.198 10 false 5 5.51,3.615 5.656,3.813 0.146,0.198 10 false 4 5.708,1.042 6.281,1.26 0.573,0.219 10 false IGCT 5.146,4.146 5.938,4.375 0.792,0.229 10 false L144 5.5,3.313 5.625,3.51 0.125,0.198 10 false 3 5.49,2.969 5.635,3.167 0.146,0.198 10 false 2 5.708,3.74 6.094,3.969 0.385,0.229 10 false GND 5.708,3.417 6.094,3.646 0.385,0.229 10 false BTH- 5.708,3.073 6.094,3.302 0.385,0.229 10 false BTH+ 5.521,4.146 6.719,4.344 1.198,0.198 10 false Battery Smart Unit 2.771,3.427 3.156,3.656 0.385,0.229 10 false BTH- 2.75,3.083 3.135,3.313 0.385,0.229 10 false BTH+ 3.219,3.417 3.438,3.615 0.219,0.198 10 false L5 3.219,3.083 3.438,3.281 0.219,0.198 10 false L5 3.219,3.26 3.438,3.458 0.219,0.198 10 false 33 3.219,2.917 3.438,3.115 0.219,0.198 10 false 32 2.729,2.021 3.26,2.25 0.531,0.229 10 false MREL 3.167,2.01 3.521,2.229 0.354,0.219 10 false A22 3.25,1.854 3.469,2.052 0.219,0.198 10 false 6 2.198,3.729 3.438,4.135 1.24,0.406 10 false Power Management Control ECU 3.167,2.375 3.521,2.583 0.354,0.208 10 false A22 3.167,2.719 3.521,2.938 0.354,0.219 10 false A21 2.854,2.375 3.24,2.604 0.385,0.229 10 false +B1 2.854,2.719 3.24,2.948 0.385,0.229 10 false +B2 3.25,2.219 3.469,2.417 0.219,0.198 10 false 5 3.25,2.552 3.469,2.75 0.219,0.198 10 false 2 0.208,0.688 0.896,0.906 0.688,0.219 10 false HV BATT 5.5,0.438 5.646,0.635 0.146,0.198 10 false 1 5.708,0.531 5.927,0.75 0.219,0.219 10 false B

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After repairing, restart the system (turn the power switch on (READY)) and recheck for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190661E03
2.51,0.49 2.896,0.646 0.385,0.156 10 false L144

Check the connections of the L144 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

3.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (B AND IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).

NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.
U190628E02
1.604,0.823 1.073,0.396 true 1.958,0.865 2.49,0.438 true 1.958,1.021 2.49,1.385 true 1.625,0.198 1.99,0.354 0.365,0.156 10 false L144 0.833,0.198 1.188,0.354 0.354,0.156 10 false GND 0.177,0.156 0.438,0.313 0.26,0.156 10 false *a 2.49,0.229 2.625,0.385 0.135,0.156 10 false B 2.521,1.323 2.948,1.479 0.427,0.156 10 false IGCT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L144-1 (B) - L144-4 (GND) Power switch off 8.6 V or more
L144-5 (IGCT) - L144-4 (GND) Power switch on (IG) 8.6 V or more


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery shield sub-assembly.



OK

NG

4.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
U190627E01
1.624,0.193 1.951,0.348 0.328,0.155 10 L144 0.651,0.258 1.009,0.413 0.358,0.155 10 GND 0.098,0.102 0.363,0.258 0.265,0.155 10 *a 1.611,0.849 1.069,0.347 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L144-4 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (B OR IGCT CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)