Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-132  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. INF Code DTC Detection Condition Trouble Area
P3004 132 The inverter is not precharged.
·

Hybrid battery junction block assembly

·

Frame wire

·

Inverter with converter assembly

·

HV battery

·

Wire harness or connector



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P3004-132 only is output, or DTC other than the one in the table below is also output. A
Following DTC is also output. B


DTC No. Relevant Diagnosis
P31AB-123 Hybrid Battery Cell Low Voltage

HINT:

P3004-132 may be output due to a malfunction which causes the DTC in the table above to be output. In this case, first troubleshoot the output DTC in the table above. Then, perform a reproduction test to check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC 3004-132 only is output, or DTCs other than the ones in the table below are also output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 658 Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0ADB-227 Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0AE6-225 Hybrid Battery Precharge Contactor Control Circuit Low
P0AE7-224 Hybrid Battery Precharge Contactor Control Circuit High
P0C76-523 Hybrid Battery System Discharge Time Too Long
P0CA3-442 DC/DC Converter Step Up Voltage Performance
P0D2E-586 Drive Motor "A" Inverter Voltage Sensor Circuit Range/Performance
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
P3004-131, 800, 801 Power Cable Malfunction
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

Table 2
DTC No. Relevant Diagnosis
P0A95-123 High Voltage Fuse
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor "A" Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor "A" Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P3004-132 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P3004-132.

Result:
Result Proceed to
All of the following conditions are met:
·

Difference between "Power Resource VB" and "VL-Voltage before Boosting" is 50 V or less.

·

Difference between "Power Resource VB" and "VH-Voltage after Boosting" is more than 70 V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 90 V.


A
In addition to the above conditions, "Batt Pack Current Val" is 3 A or more. B
Other than above C



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

C

4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
4.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

5.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY SIDE)

NG

CONNECT SECURELY

5.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY SIDE)

A

6.CHECK FRAME WIRE (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY SIDE)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK FRAME WIRE (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY SIDE)

A

7.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

7.CHECK FRAME WIRE (INVERTER WITH CONVERTER ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

OK

8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY HIGH VOLTAGE CONNECTOR)

NG

8.CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY HIGH VOLTAGE CONNECTOR)

A

9.CHECK HV BATTERY

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

9.CHECK HV BATTERY

OK

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

OK

11.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

OK

12.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

12.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

OK

13.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

15.CHECK DTC OUTPUT (HYBRID CONTROL)
15.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
DTC P3004-131 is output. B
DTC P3004-132 is output. C


HINT:

Because P3004-131 uses 2-trip detection logic, the DTC detection conditions need to be met 2 times.



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS