Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-214  Lost Communication with Airbag System Control Module  


DESCRIPTION

Refer to the description for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 214 Open or short to +B in the communication circuit
·

Wire harness or connector

·

Airbag ECU assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P3107-213 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3107-213).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

A

3.CLEAR DTC

B

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P3107-214 is not output. A
DTC P3107-214 is output again. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR)
a.
A216765E04
0.104,0 0.349,0.233 0.246,0.233 10 *a

Check the connector connections and contact pressure of the relevant terminals for the airbag ECU assembly connectors.

Text in Illustration
*a Component with harness connected
(Airbag ECU Assembly)

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG ECU ASSEMBLY)

NG

CONNECT SECURELY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG ECU ASSEMBLY)
a.

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Disconnect the L16 airbag ECU assembly connector.


c.
U191174E02
2.604,1.896 2.208,2.188 false 1.24,3.958 1.74,4.333 false 0.021,0.031 0.292,0.229 0.271,0.198 10 false *a 0.042,2.469 0.313,2.667 0.271,0.198 10 false *b 2.01,1.813 2.302,1.979 0.292,0.167 10 false L6 0.406,3.844 0.708,4.01 0.302,0.167 10 false L16 1.823,2.135 2.292,2.333 0.469,0.198 10 false ABFS 1.75,4.302 2.385,4.521 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L6-14 (ABFS) - L16-14 (GSW2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L6-14 (ABFS) or L16-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Reconnect the airbag ECU assembly connector.


e.

Reconnect the hybrid vehicle control ECU connector.



OK

9.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU
a.
U190573E02
1.688,1.385 1.958,1.552 0.271,0.167 10 false L16

Disconnect the L16 airbag ECU assembly connector.


b.

Turn the power switch on (IG).


c.
U190780E02
2.573,1.781 2.26,2.24 false 2.51,0.948 3,1.333 0.49,0.385 10 false L6 2.042,2.25 2.552,2.448 0.51,0.198 10 false ABFS 0.073,0.021 0.583,0.219 0.51,0.198 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L6-14 (ABFS) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

NOTICE:

Turning the power switch on (IG) with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the L16 airbag ECU assembly connector.



OK

NG