Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U0110-159  Lost Communication with Drive Motor Control Module "A"  U0110-656  Lost Communication with Drive Motor Control Module "A"  U0110-657  Lost Communication with Drive Motor Control Module "A"  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

The inverter with converter assembly (MG ECU) controls MG2 based on commands from the power management control ECU. The inverter with converter assembly (MG ECU) monitors communication data and detects malfunctions.


DTC No. INF Code DTC Detection Condition Trouble Area
U0110 159 Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
·

Wire harness or connector

·

Inverter with converter assembly

·

Generator cable

·

Motor cable

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

PCU fuse


656 Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
657 Error in reception from inverter with converter assembly (MG ECU) via serial communication (no reception)

WIRING DIAGRAM

A262682E15
4.224,0.391 4.623,0.552 0.399,0.161 10 CLK+ 2.468,0.391 2.867,0.552 0.399,0.161 10 CLK+ 4.224,0.882 4.623,1.042 0.399,0.161 10 CLK- 2.468,0.882 2.867,1.042 0.399,0.161 10 CLK- 4.224,1.265 4.646,1.425 0.422,0.161 10 REQ+ 2.445,1.265 2.867,1.425 0.422,0.161 10 REQ+ 4.224,2.119 4.646,2.280 0.422,0.161 10 HTM+ 2.445,2.119 2.867,2.280 0.422,0.161 10 HTM+ 4.224,2.974 4.646,3.135 0.422,0.161 10 MTH+ 2.445,2.974 2.867,3.135 0.422,0.161 10 MTH+ 0.918,3.06 1.138,3.220 0.220,0.161 10 E1 4.224,2.605 4.646,2.766 0.422,0.161 10 HTM- 2.445,2.605 2.867,2.766 0.422,0.161 10 HTM- 4.224,3.464 4.646,3.625 0.422,0.161 10 MTH- 4.117,4.015 4.539,4.176 0.422,0.161 10 A59 4.117,4.165 6.210,4.325 2.093,0.161 10 Inverter with Converter Assembly 2.445,3.464 2.867,3.625 0.422,0.161 10 MTH- 4.224,1.746 4.646,1.906 0.422,0.161 10 REQ- 2.445,1.746 2.867,1.906 0.422,0.161 10 REQ- 5.866,0.52 6.093,0.680 0.227,0.161 10 +B 5.792,0.968 6.089,1.129 0.297,0.161 10 +B2 5.694,3.07 6.102,3.230 0.408,0.161 10 GND1 5.686,3.537 6.094,3.697 0.408,0.161 10 GND2 2.924,0.494 3.212,0.655 0.288,0.161 10 A22 2.968,0.293 3.168,0.453 0.200,0.161 10 21 2.968,0.774 3.168,0.934 0.200,0.161 10 20 2.968,1.167 3.168,1.327 0.200,0.161 10 33 2.968,1.648 3.168,1.809 0.200,0.161 10 32 2.968,2.031 3.168,2.191 0.200,0.161 10 24 2.968,2.509 3.168,2.670 0.200,0.161 10 25 2.968,2.895 3.168,3.055 0.200,0.161 10 30 2.968,3.361 3.168,3.522 0.200,0.161 10 29 2.924,0.975 3.212,1.136 0.288,0.161 10 A22 2.924,1.344 3.212,1.505 0.288,0.161 10 A22 2.924,1.839 3.212,1.999 0.288,0.161 10 A22 2.924,2.203 3.212,2.364 0.288,0.161 10 A22 2.924,2.689 3.212,2.850 0.288,0.161 10 A22 2.924,3.072 3.212,3.233 0.288,0.161 10 A22 2.924,3.553 3.212,3.714 0.288,0.161 10 A22 3.911,0.414 4.034,0.575 0.123,0.161 10 5 3.872,0.886 4.072,1.046 0.200,0.161 10 15 3.943,1.273 4.142,1.434 0.200,0.161 10 6 3.872,1.754 4.072,1.915 0.200,0.161 10 16 3.911,2.116 4.034,2.277 0.123,0.161 10 8 3.872,2.614 4.072,2.774 0.200,0.161 10 18 3.911,2.976 4.034,3.136 0.123,0.161 10 7 3.872,3.468 4.072,3.629 0.200,0.161 10 17 0.599,3.046 0.886,3.207 0.288,0.161 10 L5 0.657,2.838 0.856,2.998 0.200,0.161 10 6 0.827,4.077 2.934,4.237 2.107,0.161 10 Power Management Control ECU 6.142,0.43 6.342,0.591 0.200,0.161 10 10 6.142,0.879 6.342,1.039 0.200,0.161 10 9 6.142,2.98 6.342,3.141 0.200,0.161 10 28 6.142,3.45 6.342,3.610 0.200,0.161 10 27 6.555,0.681 6.917,0.842 0.362,0.161 10 PCU 4.766,0.76 4.935,0.924 0.169,0.164 10 * 2.205,0.764 2.336,0.928 0.131,0.164 10 * 2.205,1.62 2.336,1.784 0.131,0.164 10 * 2.205,2.487 2.336,2.651 0.131,0.164 10 * 2.205,3.341 2.336,3.505 0.131,0.164 10 * 4.766,1.623 4.935,1.787 0.169,0.164 10 * 4.766,2.478 4.935,2.642 0.169,0.164 10 * 4.766,3.337 4.935,3.501 0.169,0.164 10 * 0.426,4.507 1.904,4.671 1.478,0.164 10 *: Approximately 120 Ω 6.51,0.416 6.709,0.577 0.200,0.161 10 2 6.86,0.416 7.060,0.577 0.200,0.161 10 1 6.726,1.234 7.147,1.819 0.421,0.585 10 from IGCT Relay

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

If any of the DTCs U0110-159, U0110-656, and U0110-657 was set due to incomplete engagement of the connectors, and if the system returns to normal when the power switch is turned on (IG) after clearing the DTCs, DTC P324E-788 will be set. Proceed to troubleshooting without considering DTC P324E-788.



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 2 minutes or more.



PROCEDURE

1.CHECK FUSE (PCU)
a.

Remove the PCU fuse from the engine room relay block and junction block assembly.


b.
A237660E04
2.198,2.031 2.938,2.094 false 0.094,0.083 0.313,0.313 0.219,0.229 10 false *1 2.969,2.031 3.188,2.26 0.219,0.229 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PCU fuse terminals Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 PCU Fuse


c.

Install the PCU fuse.



OK

2.CLEAR DTC

NG

18.REPLACE FUSE (PCU)
2.CLEAR DTC

NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC U0110-159, 656 or 657 is output. A
DTC U0110-159, 656 and 657 are not output. B



e.

Turn the power switch off.



A

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

B

4.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

5.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

22.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)
7.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

24.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.
U154307E03
2.135,0.979 2,0.313 false 2.281,0.979 2.448,0.313 false 2.01,1.677 2.135,1.198 false 2.479,1.677 2.281,1.198 false 1.833,0.104 2.146,0.292 0.313,0.188 10 false +B2 1.604,1.729 2.094,1.917 0.49,0.188 10 false GND2 2.396,1.729 2.885,1.917 0.49,0.188 10 false GND1 2.396,0.104 2.708,0.292 0.313,0.188 10 false +B 0.146,0.094 0.458,0.281 0.313,0.188 10 false *a 0.344,1.063 0.667,1.25 0.323,0.188 10 false A59

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-28 (GND1) - Body ground Power switch off Below 1 Ω
A59-27 (GND2) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A59-10 (+B) - Body ground Power switch on (IG) 11 to 14 V
A59-9 (+B2) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Reconnect the A59 inverter with converter assembly connector.



OK

9.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A379342E02
1.24,1.667 1.594,1.208 false 1.719,1.688 1.625,1.208 false 2.146,1.74 1.76,1.083 false 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.281,0.458 1.594,0.656 0.313,0.198 10 false A22 1.865,0.458 2.177,0.656 0.313,0.198 10 false L5 0.979,1.719 1.385,1.938 0.406,0.219 10 false CLK+ 2.094,1.76 2.406,1.958 0.313,0.198 10 false E1 0.094,3.063 0.406,3.26 0.313,0.198 10 false CH1 2.792,3.448 3.219,3.677 0.427,0.229 10 false GND 0.115,3.813 0.427,4.01 0.313,0.198 10 false CH2 2.781,4.01 3.208,4.24 0.427,0.229 10 false GND 1.521,1.74 1.927,1.958 0.406,0.219 10 false CLK-

Measure the waveform.

Item Contents
Tester Connection CH1: A22-21 (CLK+) - L5-6 (E1)
CH2: A22-20 (CLK-) - L5-6 (E1)
Equipment Setting 1V/DIV., 1μs/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

B

12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
10.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A379343E02
2.094,1.688 1.76,1.094 false 1.615,1.646 1.385,1.26 false 1.146,1.667 1.354,1.26 false 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.281,0.458 1.594,0.656 0.313,0.198 10 false A22 1.865,0.458 2.177,0.656 0.313,0.198 10 false L5 0.927,1.688 1.385,1.906 0.458,0.219 10 false REQ+ 2.031,1.708 2.344,1.906 0.313,0.198 10 false E1 2.719,3.51 3.177,3.708 0.458,0.198 10 false GND 0.198,3.146 0.51,3.344 0.313,0.198 10 false CH1 1.479,1.688 1.938,1.906 0.458,0.219 10 false REQ- 0.167,3.875 0.479,4.073 0.313,0.198 10 false CH2 2.719,4.083 3.177,4.281 0.458,0.198 10 false GND

Measure the waveform.

Item Contents
Tester Connection CH1: A22-33 (REQ+) - L5-6 (E1)
CH2: A22-32 (REQ-) - L5-6 (E1)
Equipment Setting 1V/DIV., 1ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

11.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)

B

14.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
11.CHECK POWER MANAGEMENT CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the power management control ECU terminals specified in the following table.


b.

Turn the power switch on (IG).


c.
A379344E02
1.76,1.083 2.073,1.656 false 1.271,1.635 1.552,1.26 false 1.688,1.646 1.594,1.26 false 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.271,0.458 1.583,0.656 0.313,0.198 10 false A22 1.865,0.458 2.177,0.656 0.313,0.198 10 false L5 1.052,1.667 1.51,1.885 0.458,0.219 10 false MTH+ 2.042,1.698 2.354,1.896 0.313,0.198 10 false E1 2.792,3.49 3.177,3.708 0.385,0.219 10 false GND 0.281,3.104 0.594,3.302 0.313,0.198 10 false CH1 1.573,1.677 2.031,1.896 0.458,0.219 10 false MTH- 0.25,3.865 0.563,4.063 0.313,0.198 10 false CH2 2.792,4.063 3.177,4.281 0.385,0.219 10 false GND

Measure the waveform.

Item Contents
Tester Connection CH1: A22-30 (MTH+) - L5-6 (E1)
CH2: A22-29 (MTH-) - L5-6 (E1)
Equipment Setting 1V/DIV., 200μs/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

HINT:
·

Inspect with the connector connected.

·

If pulses are generated, the shape of the waveform can be assumed to be normal.

·

The shape of the waveform may vary according to communication conditions.




d.

Turn the power switch off.



A

B

16.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A22 power management control ECU connector.


c.

Disconnect the A59 inverter with converter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U154321E03
1.688,2.208 1.969,2.604 false 1.646,2.208 1.104,2.604 false 1.563,3.604 0.958,4.313 false 1.552,3.708 1.938,4.302 false 0.104,0.115 0.396,0.354 0.292,0.24 10 false *a 0.104,2.917 0.396,3.156 0.292,0.24 10 false *b 0.729,2.583 1.25,2.781 0.521,0.198 10 false CLK+ 1.844,2.615 2.25,2.802 0.406,0.188 10 false CLK- 0.656,4.333 1.177,4.49 0.521,0.156 10 false CLK+ 1.771,4.344 2.292,4.5 0.521,0.156 10 false CLK- 1.979,2.094 2.25,2.26 0.271,0.167 10 false A22 0.521,3.688 0.792,3.854 0.271,0.167 10 false A59

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-21 (CLK+) - Body ground Power switch on (IG) Below 1 V
A22-20 (CLK-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-21 (CLK+) - A59-5 (CLK+) Power switch off Below 1 Ω
A22-20 (CLK-) - A59-15 (CLK-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-21 (CLK+) or A59-5 (CLK+) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-20 (CLK-) or A59-15 (CLK-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the A59 inverter with converter assembly connector.


k.

Reconnect the A22 power management control ECU connector.



OK

13.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the A22 power management control ECU connector.


b.
U154238E03
1.625,2.5 1.427,3.021 false 1.677,2.51 1.875,3.031 false 0.688,2.302 0.958,2.469 0.271,0.167 10 false A22 1.177,3.052 1.563,3.219 0.385,0.167 10 false CLK+ 1.75,3.052 2.188,3.219 0.438,0.167 10 false CLK- 0.229,0.198 0.427,0.365 0.198,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-21 (CLK+) - A22-20 (CLK-) Power switch off 80 to 170 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Reconnect the A22 power management control ECU connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

14.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A22 power management control ECU connector.


c.

Disconnect the A59 inverter with converter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U154322E03
1.406,2.271 1.969,2.604 false 1.365,2.271 1.073,2.604 false 1.646,3.604 1.042,4.313 false 1.635,3.708 2.031,4.302 false 0.104,0.115 0.396,0.354 0.292,0.24 10 false *a 0.104,2.917 0.396,3.156 0.292,0.24 10 false *b 0.729,2.604 1.25,2.76 0.521,0.156 10 false REQ+ 1.854,2.604 2.375,2.76 0.521,0.156 10 false REQ- 1.979,2.083 2.25,2.25 0.271,0.167 10 false A22 0.51,3.688 0.781,3.854 0.271,0.167 10 false A59 0.781,4.333 1.302,4.49 0.521,0.156 10 false REQ+ 1.896,4.344 2.417,4.5 0.521,0.156 10 false REQ-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-33 (REQ+) - Body ground Power switch on (IG) Below 1 V
A22-32 (REQ-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-33 (REQ+) - A59-6 (REQ+) Power switch off Below 1 Ω
A22-32 (REQ-) - A59-16 (REQ-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-33 (REQ+) or A59-6 (REQ+) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-32 (REQ-) or A59-16 (REQ-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the A59 inverter with converter assembly connector.


k.

Reconnect the A22 power management control ECU connector.



OK

15.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Disconnect the A22 power management control ECU connector.


b.
U154239E03
1.354,2.573 1.146,2.969 false 1.396,2.573 1.604,2.969 false 0.688,2.396 0.958,2.563 0.271,0.167 10 false A22 0.896,2.99 1.323,3.156 0.427,0.167 10 false REQ+ 1.479,2.99 1.917,3.156 0.438,0.167 10 false REQ- 0.25,0.229 0.448,0.396 0.198,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-33 (REQ+) - A22-32 (REQ-) Power switch off 80 to 170 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Reconnect the A22 power management control ECU connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

16.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A22 power management control ECU connector.


c.

Disconnect the A59 inverter with converter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U154323E03
1.646,2.281 1.969,2.615 false 1.594,2.281 1.073,2.615 false 1.719,3.625 1.115,4.333 false 1.719,3.708 2.115,4.302 false 0.104,0.115 0.396,0.354 0.292,0.24 10 false *a 0.104,2.917 0.396,3.156 0.292,0.24 10 false *b 0.729,2.615 1.25,2.771 0.521,0.156 10 false MTH+ 1.844,2.635 2.365,2.792 0.521,0.156 10 false MTH- 1.969,2.094 2.24,2.26 0.271,0.167 10 false A22 0.51,3.688 0.781,3.854 0.271,0.167 10 false A59 0.875,4.323 1.396,4.479 0.521,0.156 10 false MTH+ 2,4.323 2.521,4.479 0.521,0.156 10 false MTH-

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-30 (MTH+) - Body ground Power switch on (IG) Below 1 V
A22-29 (MTH-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-30 (MTH+) - A59-7 (MTH+) Power switch off Below 1 Ω
A22-29 (MTH-) - A59-17 (MTH-) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-30 (MTH+) or A59-7 (MTH+) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-29 (MTH-) or A59-17 (MTH-) - Body ground and other terminals Power switch off 10 kΩ or higher



i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Reconnect the A59 inverter with converter assembly connector.


k.

Reconnect the A22 power management control ECU connector.



OK

17.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.
U154401E03
1.573,1.906 1.365,2.427 false 1.625,1.906 1.833,2.427 false 1.271,1.052 1.542,1.219 0.271,0.167 10 false A22 1.104,2.458 1.542,2.625 0.438,0.167 10 false MTH+ 1.688,2.458 2.125,2.625 0.438,0.167 10 false MTH- 0.229,0.229 0.427,0.396 0.198,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-30 (MTH+) - A22-29 (MTH-) Power switch off 80 to 170 Ω


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


d.

Reconnect the A59 inverter with converter assembly connector.



OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

18.REPLACE FUSE (PCU)
a.
A237660E04
2.198,2.031 2.938,2.094 false 0.094,0.083 0.313,0.313 0.219,0.229 10 false *1 2.969,2.031 3.188,2.26 0.219,0.229 10 false *2

Replace the PCU fuse.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 PCU Fuse


b.

Turn the power switch on (READY).


c.

Check if there is an open circuit in the PCU fuse in engine room relay block and junction block assembly.

OK:

There is no open circuit in the PCU fuse.


HINT:

If the fuse does not become open again after turning the power switch on (READY), it can be assumed that the previous fuse failed due to age.



d.

Turn the power switch off.



OK

COMPLETED

NG

19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
19.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A237660E04
2.198,2.031 2.938,2.094 false 0.094,0.083 0.313,0.313 0.219,0.229 10 false *1 2.969,2.031 3.188,2.26 0.219,0.229 10 false *2

Remove the PCU fuse from the engine room relay block and junction block assembly.

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 PCU Fuse


c.

Disconnect the A59 inverter with converter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

U190604E02
2.271,1.417 2.469,2.188 false 2.156,1.406 1.948,2.198 false 0.875,0.156 1.167,0.49 0.292,0.333 10 false *a 3.906,0.146 4.198,0.479 0.292,0.333 10 false *1 6.479,0.823 6.771,1.156 0.292,0.333 10 false *2 2.417,2.208 2.781,2.438 0.365,0.229 10 false +B 1.833,2.219 2.198,2.448 0.365,0.229 10 false +B2 0.708,1.448 0.99,1.615 0.281,0.167 10 false A59

Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly *2 PCU Fuse
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A59-10 (+B) - 2 (PCU fuse terminal) Power switch off Below 1 Ω
A59-9 (+B2) - 2 (PCU fuse terminal) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A59-10 (+B), A59-9 (+B2) or 2 (PCU fuse terminal) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Reconnect the A59 inverter with converter assembly connector.


f.

Install the PCU fuse.



OK

20.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

21.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

REPLACE FUSE (PCU)

21.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

22.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

23.CHECK GENERATOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

24.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

25.CHECK MOTOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY