Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301574 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0B3D-123  Hybrid Battery Voltage Sensor "A" Circuit Low  P0B42-123  Hybrid Battery Voltage Sensor "B" Circuit Low  P0B47-123  Hybrid Battery Voltage Sensor "C" Circuit Low  P0B4C-123  Hybrid Battery Voltage Sensor "D" Circuit Low  P0B51-123  Hybrid Battery Voltage Sensor "E" Circuit Low  P0B56-123  Hybrid Battery Voltage Sensor "F" Circuit Low  P0B5B-123  Hybrid Battery Voltage Sensor "G" Circuit Low  P0B60-123  Hybrid Battery Voltage Sensor "H" Circuit Low  P0B65-123  Hybrid Battery Voltage Sensor "I" Circuit Low  


DESCRIPTION

Refer to the description for DTC P0A80-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A80-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0B3D
P0B42
P0B47
P0B4C
P0B51
P0B56
P0B5B
P0B60
P0B65
123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
·

Battery smart unit

·

HV battery



HINT:
·

Values smaller than 2.8 V may not be shown in the Data List because a fail-safe value is substituted.

·

Hybrid battery voltage sensor in the DTC titles refers to the battery smart unit.



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION)

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)

A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)

A

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY SMART UNIT CONNECTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL).


c.
A251526

Check the connections of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

4.REPLACE BATTERY SMART UNIT

NG

CONNECT SECURELY

4.REPLACE BATTERY SMART UNIT

NEXT

5.CLEAR DTC (HV)
5.CLEAR DTC (HV)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

NOTICE:

When DTCs are cleared, freeze frame data and INF codes are also cleared.



e.

Turn the power switch off.


f.

Perform a reproduction test.



NEXT

6.RECONFIRM DTC OUTPUT (HV)
6.RECONFIRM DTC OUTPUT (HV)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Result:
Result Proceed to
Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are not output A
Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are output B




A

RETURNS TO NORMAL OPERATION

B