Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL SYSTEM › 2014.11–2019.03
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301602 FUEL SYSTEM L

2ZR-FXE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTIONS


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep gasoline away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

Remove the rear No. 1 seat assembly (for Side) (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for Side)>REMOVAL).


b.

Remove the rear No. 1 seat assembly (for Center) (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for Center)>REMOVAL).


c.

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY>REMOVAL).


d.

Remove the rear floor service hole cover (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL PUMP>REMOVAL).


e.
A248044

Disconnect the fuel pump connector.


f.

Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


g.

Start the engine.


h.

After the engine has stopped on its own, turn the power switch off.


i.

Crank the engine again and make sure that the engine does not start.

HINT:

Some DTCs may be stored. Clear the DTCs before proceeding to the next step (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).



j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



k.

Connect the fuel pump connector.


l.

Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.


m.

Install the rear floor service hole cover with new butyl tape (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL PUMP>INSTALLATION).


n.

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY>INSTALLATION).


o.

Install the rear No. 1 seat assembly (for Center) (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for Center)>INSTALLATION).


p.

Install the rear No. 1 seat assembly (for Side) (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for Side)>INSTALLATION).



FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of gasoline will spray out. Perform the following procedure:

i.

Discharge the fuel system pressure.


ii.

Disconnect the fuel tank main tube sub-assembly.


iii.

Drain the fuel remaining inside the fuel tank main tube sub-assembly into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.
A076220E66
2.188,0.76 2.26,0.406 false 2.26,1.583 2.26,1.885 false 0.573,1.375 0.573,1.708 false 1.385,0.875 1.115,0.438 1.115,0.438 1.583,0.875 false 2.917,1.333 2.917,1.542 false 2.26,0.406 2.438,0.406 false 0.969,0.302 1.167,0.5 0.198,0.198 10 false *2 2.479,0.333 3.125,0.531 0.646,0.198 10 false *1 2.844,1.552 3.073,1.75 0.229,0.198 10 false *5 0.5,1.698 0.688,1.896 0.188,0.198 10 false *3 2.188,1.896 2.396,2.094 0.208,0.198 10 false *4

Perform the following procedure when disconnecting a fuel delivery pipe (metallic type):

Text in Illustration
*1 Retainer
*2 O-ring
*3 Nylon Tube
*4 Fuel Tube Connector
*5 Fuel Pipe

HINT:

The structure of a fuel tube connector is as shown in the illustration.


i.

Check if there is any damage or foreign matter on the fuel pipe connections.


ii.
U110396E04
1.167,0.573 1.49,0.25 false 1.521,0.146 2.219,0.563 0.698,0.417 10 false *1 0.917,3.875 1.104,4.146 0.188,0.271 10 false *a 2.427,3.917 2.594,4.208 0.167,0.292 10 false *b

Remove the No. 2 fuel pipe clamp.

Text in Illustration
*1 No. 2 Fuel Pipe Clamp
*a Type A
*b Type B

NOTICE:

Do not reuse the fuel pipe clamp (Type B).



iii.
A062165E16
2,0.719 2.469,1.51 2.469,1.51 2,1.802 false 2.5,1.448 2.802,1.594 0.302,0.146 10 false SST

Assemble SST to the fuel tube connector as shown in the illustration.

SST
09268-21011  


iv.
A062156E19
2.104,1.167 2.271,0.344 2.271,0.344 2.104,0.344 false 0.677,1.281 0.885,1.438 0.208,0.156 10 false *1 1.604,1.115 1.792,1.271 0.188,0.156 10 false *a 1.792,0.26 2.115,0.417 0.323,0.156 10 false SST 2.354,1.552 2.542,1.708 0.188,0.156 10 false *b

Turn SST, align the retainers inside the fuel tube connector with the SST chamfers and insert SST into the fuel tube connector.

Text in Illustration
*1 Retainer (4 places)
*a Turn
*b Push


v.

Slide SST and the fuel tube connector together towards the fuel tube assembly.



c.

Perform the following procedure when connecting a fuel tube connector (metallic type):

i.

Check if there is any damage or foreign matter on the fuel pipe connections.


ii.
A142841E02
1.78,0.608 1.938,0.803 0.158,0.195 10 *a 1.824,2.782 1.999,3.009 0.175,0.227 10 *b

Match the axis of the fuel tube connector with the axis of the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.

Text in Illustration
*a Push
*b Pull


iii.

After connecting, check that the fuel pipe and the fuel tube connector are securely connected by pulling on them.


iv.
U110397E04
1.146,0.573 1.469,0.25 false 1.521,0.104 1.823,0.521 0.302,0.417 10 false *1 0.938,3.875 1.167,4.177 0.229,0.302 10 false *a 2.479,3.938 2.656,4.198 0.177,0.26 10 false *b

Install the No. 2 fuel pipe clamp. (Type A)

Text in Illustration
*1 No. 2 Fuel Pipe Clamp
*a Type A
*b Type B


v.

Install a new No. 2 fuel pipe clamp. (Type B)




d.

Perform the following procedure when disconnecting a fuel tube connector (quick type A):

i.
A216403

Release the claw and remove the No. 1 fuel pipe clamp.


ii.
A099425E33
1.552,1.177 1.552,1.573 false 1.479,1.583 1.677,1.781 0.198,0.198 10 false *1

Disengage the lock claws by raising the fuel tube connector cover as shown in the illustration.

Text in Illustration
*1 Fuel Tube Connector Cover


iii.

Check that there is no dirt or other foreign matter on the fuel pipe and contact surface before disconnecting them. Clean them if necessary.


iv.

Disconnect the fuel tube connector from the fuel pipe by hand.


v.
A159424E53
2.677,1.198 2.5,1.271 false 2.677,1.198 2.563,1.479 false 2.021,3.719 2.115,3.948 true 2.198,3.708 2.115,3.938 true 2.635,3.396 2.406,2.75 2.406,2.75 2.146,2.75 true 1.667,1.927 1.854,2.281 0.188,0.354 10 false *a 1.271,0.448 1.458,0.802 0.188,0.354 10 false *a 0.656,1.958 0.823,2.313 0.167,0.354 10 false *b 2.698,1.104 2.865,1.458 0.167,0.354 10 false *1 1.99,2.667 2.188,3.021 0.198,0.354 10 false *1 2.031,3.948 2.208,4.177 0.177,0.229 10 false *2

If the fuel tube connector and the fuel pipe are stuck, push in and pull on the fuel tube connector to release them. Pull the fuel tube connector out of the fuel pipe carefully.

Text in Illustration
*1 Retainer
*2 O-ring
*a Pinch
*b Pull Out


vi.

Check that there is no dirt or other foreign matter on the contact surface of the disconnected fuel pipe. Clean them away if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Perform the following procedure when connecting a fuel tube connector (quick type A):

i.
A121423E06
1.047,1.72 1.242,1.895 0.194,0.174 10 *a 1.931,4.134 2.110,4.318 0.178,0.184 10 *b

Check if there is any damage or foreign matter on the fuel pipe connections.

Text in Illustration
*a Push
*b Pull


ii.

Match the axis of the fuel tube connector with the axis of the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe.


iii.

After connecting, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iv.
A379360E02
1.542,1.177 1.542,1.51 false 1.469,1.542 1.781,1.74 0.313,0.198 10 false *1

Engage the lock claws to the fuel tube connector by pushing down on the fuel tube connector cover.

Text in Illustration
*1 Fuel Tube Connector Cover



vi.
A216403

Engage the lock claw and install the No. 1 fuel pipe clamp.



f.
U154455E01
0.995,3.778 1.174,4.004 0.179,0.226 10 *1 1.521,3.662 1.319,3.863 1.319,3.863 1.205,3.863 false

Perform the following procedure when disconnecting a fuel tube connector (quick type B):

Text in Illustration
*1 Retainer

i.

Check that there is no damage or foreign matter on the part of the fuel pipe that contacts the fuel tube connector.


ii.

Using a screwdriver with its tip wrapped with protective tape, pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube.


iii.

If the fuel tube connector and fuel pipe are stuck, pinch the fuel pipe by hand and push or pull the fuel tube connector to disconnect it.


iv.

Check for foreign matter on the seal surface of the disconnected fuel pipe. Clean it if necessary.


v.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Perform the following procedure when connecting a fuel tube connector (quick type B):

i.

Check that there are no scratches or foreign matter around the connected part of the fuel tube connector and fuel pipe.


ii.
U154456E01
0.995,3.778 1.174,4.004 0.179,0.226 10 *1 1.521,3.662 1.319,3.863 1.319,3.863 1.205,3.863 false

Align the fuel tube connector with the fuel pipe, connect the fuel tube connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer. If the connection is tight, apply a small amount of clean engine oil to the tip of the fuel pipe.

Text in Illustration
*1 Retainer


iii.

After connecting the fuel pipes, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.

Observe the following precautions when handling a nylon tube.

i.

Do not twist the connection part of the nylon tube and the fuel tube connector when connecting them.


ii.

Do not bend, kink, or twist the nylon tube.


iii.

Do not remove the EPDM protector on the outside of the nylon tube.


iv.

Do not close the piping by kinking the nylon tube.




INJECTOR


a.
A222009E02
0.229,0.158 0.419,0.358 0.190,0.200 10 *a 0.226,1.345 0.430,1.535 0.204,0.190 10 *b 0.457,2.75 0.622,2.970 0.165,0.220 10 *1 1.257,2.921 1.433,3.111 0.177,0.190 10 *2 0.749,2.37 0.543,2.57 0.543,2.57 0.543,2.713 false 1.353,2.547 1.353,2.902 false 0.138,0.068 3.17,1.192 3.033,1.124 0.133,1.272 3.165,3.201 3.033,1.929

Observe the following precautions when removing and installing a fuel injector:

Text in Illustration
*1 O-ring
*2 Delivery Pipe
*a CORRECT
*b INCORRECT

i.

Do not reuse the O-ring and insulator.


ii.

When placing a new O-ring onto the injector, do not damage the new O-ring.


iii.

Coat the new O-ring with grease or gasoline before installing it. Do not use engine oil, gear oil or brake fluid.



b.
A217166E08
2.393,0.295 2.08,0.151 2.08,0.151 1.538,0.151 false 2.504,0.658 3.004,0.926 false 1.117,1.528 0.622,1.033 0.622,1.033 0.458,1.033 false 1.327,0.057 1.53,0.345 0.203,0.288 10 *1 3.032,0.832 3.26,1.117 0.228,0.286 10 *2 0.253,0.943 0.49,1.193 0.237,0.25 10 *3

Install the injector into the delivery pipe and cylinder head as shown in the illustration. Apply grease or gasoline to the contact surfaces of the injector before installing the injector.

Text in Illustration
*1 Delivery Pipe
*2 O-ring
3 Insulator



FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


a.
A217141E05
1.167,1.01 0.885,1.01 false 0.708,0.927 0.875,1.229 0.167,0.302 10 false *1

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is welded to the plate.

Text in Illustration
*1 Tube



INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).