Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL INJECTOR › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301603 FUEL INJECTOR A

2ZR-FXE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

a.
A153011E16
1.052,0.417 0.719,0.417 false 2.052,1.406 2.406,1.406 false 0.521,0.313 0.708,0.49 0.188,0.177 10 false *1 2.438,1.313 2.625,1.49 0.188,0.177 10 false *2

Install a new insulator and O-ring to each fuel injector assembly.

Text in Illustration
*1 O-ring
*2 Insulator


b.

Apply a light coat of gasoline or spindle oil to the contact surfaces of the new O-ring on each fuel injector assembly.


c.
A173350

While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.

NOTICE:
·

Do not damage the fuel injector assembly or O-ring.

·

Do not twist the O-ring.

·

After installing each fuel injector, check that it turns smoothly. If not, replace the O-ring with a new one.




Hide 23807V 2.INSTALL NO. 1 DELIVERY PIPE SPACER

a.
A245591E01
1.973,1.023 2.160,1.230 0.186,0.207 10 *a 2.02,1.723 2.206,1.930 0.186,0.207 10 *b

Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

Text in Illustration
*a Delivery Pipe Side
*b Cylinder Head Side

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23807 3.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies and install the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.

·

Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.




b.

Install the bolt to secure the fuel delivery pipe sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23901 4.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
U110523

Push the tube connector into the pipe until the tube connector makes a "click" sound.

NOTICE:
·

Before connecting the connector and fuel pipe, check that there is no damage or foreign matter on the connecting part of the fuel pipe.

·

After connecting the fuel tube connector and pipe, check that they are securely connected by pulling on them.




b.

Engage the lock claw to install the No. 1 fuel pipe clamp.


Hide 82121 5.CONNECT ENGINE WIRE

a.

Install the bolt.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


b.

Connect the 4 fuel injector connectors.


c.

Connect the 4 connectors.


d.

Attach the 2 clamps to connect the engine wire.


Hide 25601L 6.INSTALL EGR WITH COOLER PIPE SUB-ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).