Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301638 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 88211B 1.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

E219893E01
1.553,0 1.834,0.281 0.281,0.281 10 *a 0.72,0.885 1.001,1.166 0.281,0.281 10 *b

Text in Illustration
*a Approximately 10 m (32.8 ft.)
*b Approximately 14 m (45.9 ft.)

CAUTION:

Radio frequency radiation exposure information:

·

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

·

This equipment should be kept with minimum distance of 20 cm (7.87 in.) between the radiator (antenna) and your body at all times during adjustment.

·

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.



NOTICE:
·

Perform measurements on a level surface.

·

Make sure that no large pieces of metal are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.



a.

Before adjusting the radar beam axis, prepare the vehicle as follows.

i.

Check the tire pressure and adjust it if necessary.


ii.

Remove all excess weight from the vehicle (luggage, heavy objects, etc.).


iii.

Remove the radiator support opening cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>REMOVAL).



b.
E219894E01
2.437,0.196 2.718,0.477 0.281,0.281 10 *1 2.069,0.564 2.398,0.283 false

Check and adjust the vertical direction of the radar sensor.

Text in Illustration
*1 Level

i.

Remove dust, oil and foreign matter from the radar sensor's level rack.


ii.

Set a level on the radar sensor's level rack.


iii.
E223552E01
1.522,1.853 1.803,2.134 0.281,0.281 10 *1 1.742,1.624 1.62,1.82 false 2.054,1.351 2.382,1.843 false 0.89,3.239 1.06,2.692 false 1.102,2.594 1.382,2.875 0.281,0.281 10 *2 1.052,0.835 1.333,1.116 0.281,0.281 10 *c 0.433,1.446 0.714,1.727 0.281,0.281 10 *b 2.317,1.868 2.597,2.149 0.281,0.281 10 *a 2.258,1.121 2.699,1.121 false 2.738,1.04 3.040,1.360 0.302,0.320 10 0°

Check that the level's air bubble is within the red frame.

Text in Illustration
*1 Level
*2 Bolt A
*a Air Bubble
*b Vehicle Front
*c LH

OK:

Level's air bubble is within red frame.


If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the air bubble is within the red frame.

HINT:
·

The adjustable range within the level's red frame is +/- 0.2°.

·

The target angle is +0.2° (upward angle of 0.2°).

Adjustment:
Adjustment Direction Adjustment Procedure Adjustment Angle
Vertical adjustment Upward direction: Turn screwdriver to negative (-) side When screwdriver is turned once, adjustment changes by about 0.12°.
Downward direction: Turn screwdriver to positive (+) side






c.
E219895E02
0.99,1.281 1.333,0.646 1.333,0.646 0.781,0.969 false 1.375,1.531 1.323,1.813 false 1.396,0.521 1.813,0.74 0.417,0.219 10 false SST 1.229,1.833 1.51,2.115 0.281,0.281 10 false *1

Adjust the reflector height.

Text in Illustration
*1 Millimeter Wave Radar Sensor

i.

Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor or the center of the emblem.

SST
09870-60000  (09870-60010)
09870-60040  

HINT:

Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob), and a 5 m (16.4 ft.) tape measure.




d.
E223559E01
0.852,0.416 1.259,0.568 0.407,0.152 10 5 m

Place the reflector.

i.

Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle.


ii.
E223560E02
1.708,1.083 1.333,1.385 1.333,1.385 1.333,1.552 false 0.542,0.156 0.823,0.438 0.281,0.281 10 false *a 1.271,1.594 1.552,1.875 0.281,0.281 10 false *b

Set one end of the 10 m (32.8 ft.) string on the vehicle's rear center point. Run the string over the vehicle's front center point to a position 5 m (16.4 ft.) beyond the vehicle's front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.

Text in Illustration
*a Adjust center by moving string to right and left
*b Extend string through front center mark


iii.

Place the reflector (SST) at the marked position.

NOTICE:

Perform the operation as precisely as possible.


E223550E03
0.792,1.427 1.156,0.969 false 4.021,1.542 3.375,2.125 false 1.188,0.854 1.469,1.135 0.281,0.281 10 false *a 3.219,2.115 3.5,2.396 0.281,0.281 10 false *b 2.25,0.167 2.615,0.448 0.365,0.281 10 false 5 m 0.083,1.385 0.604,1.667 0.521,0.281 10 false 13 mm

Text in Illustration
*a Reflector Placement Point *b Millimeter Wave Radar Sensor Position



e.

Check the radar beam axis.

i.

When using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on, and turn the cruise control main switch on.

4.

Select "Connect to Vehicle".

5.

Select each item on the display screen and proceed to the next screen.

6.

Under "System Selection Menu", select "Radar Cruise".

7.

Select "Utility".

8.

Select "Beam Axis Adjustment" and proceed to the next screen.

HINT:

A buzzer will sound for 1 second.


9.

Follow the tester display, and continue with the adjustment.

CAUTION:

Do not come within 20 cm (7.87 in.) of the radar sensor.


NOTICE:
·

Turn the cruise control main switch on before pressing Next.

·

Make sure that there is at least 20 cm (7.87 in.) between the radar sensor and any nearby individuals.





ii.

Check the following items on the radar cruise divergence data screen.

NOTICE:

While using the GTS beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the GTS data. In such a case, the deviation is displayed on the combination meter's multi-information display.


1.

Confirm that the distance value is approximately 5 m (16.4 ft.).

HINT:
·

A value between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.) is indicated.

·

If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the notice at the beginning of this adjustment procedure).



2.

Confirm that the left/right side value is between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.).

HINT:

If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the notice at the beginning of this adjustment procedure).





f.

Check and adjust the horizontal direction of the radar sensor.

i.

Check that the divergence of the radar beam axis is 0°.

Standard:

0° (Both right and left)


If the axis is not as specified, use a screwdriver to adjust bolt B until the divergence of the radar beam axis is 0°.


ii.
E223551E01
2.563,0.899 2.254,0.318 false 2.034,0.225 2.310,0.426 0.276,0.201 10 *1

Based on the measured divergence of the beam axis, turn and adjust bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.

Text in Illustration
*1 Bolt B

Adjustment:
Adjustment Direction Adjustment Procedure Adjustment Angle
Horizontal adjustment Right direction: Turn screwdriver to positive (+) side. When screwdriver is turned once, adjustment changes by about 0.07°.
Left direction: Turn screwdriver to negative (-) side.


HINT:

If the value does not change to 0°, it is possible that the sensor is aiming at something different. Reconfirm that there are no reflective materials in the surrounding area.



iii.

Select "Next". The driving learning value is automatically reset.

HINT:

A buzzer will sound for 10 seconds or more.



iv.

Disconnect the GTS from the DLC3.



g.

Recheck and readjust the vertical direction of the radar sensor.

i.
E219894E01
2.437,0.196 2.718,0.477 0.281,0.281 10 *1 2.069,0.564 2.398,0.283 false

Set a level on the radar sensor's level rack.

Text in Illustration
*1 Level


ii.
E223552E01
1.522,1.853 1.803,2.134 0.281,0.281 10 *1 1.742,1.624 1.62,1.82 false 2.054,1.351 2.382,1.843 false 0.89,3.239 1.06,2.692 false 1.102,2.594 1.382,2.875 0.281,0.281 10 *2 1.052,0.835 1.333,1.116 0.281,0.281 10 *c 0.433,1.446 0.714,1.727 0.281,0.281 10 *b 2.317,1.868 2.597,2.149 0.281,0.281 10 *a 2.258,1.121 2.699,1.121 false 2.738,1.04 3.040,1.360 0.302,0.320 10 0°

Check that the level's air bubble is within the red frame.

Text in Illustration
*1 Level
*2 Bolt A
*a Air Bubble
*b Vehicle Front
*c LH

OK:

Level's air bubble is within the red frame.


If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.

HINT:
·

The adjustable range within the red frame is +/- 0.2°.

·

The target angle is +0.2° (upward angle of 0.2°).

Adjustment:
Adjustment Direction Adjustment Procedure Adjustment Angle
Vertical adjustment Upward direction: Turn screwdriver to negative (-) side When screwdriver is turned once, adjustment changes by about 0.12°.
Downward direction: Turn screwdriver to positive (+) side






h.

After adjusting the radar beam axis, return the vehicle to its original condition.

i.

If any heavy items were removed from the vehicle, return them (luggage, heavy objects, etc.).


ii.

Install the radiator support opening cover (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION).