Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0122  Lost Communication with Vehicle Dynamics Control Module  U0123  Lost Communication with Yaw Rate Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  U0293  Lost Communication with HV ECU  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

These DTCs are stored when a communication malfunction occurs between the sensors and ECUs.

DTC No. DTC Detection Condition Trouble Area
U0122 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication stop between skid control ECU and driving support ECU assembly continues for 3 seconds or more
·

Brake booster with master cylinder (skid control ECU)

·

Power management control ECU

·

Driving support ECU assembly

·

CAN communication system


U0123 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication stop between yaw rate sensor and driving support ECU assembly continues for 1 second or more
·

Yaw rate sensor

·

Power management control ECU

·

Driving support ECU assembly

·

CAN communication system


U0126 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication stop between steering angle sensor and driving support ECU assembly continues for 1 second or more
·

Steering angle sensor

·

Power management control ECU

·

Driving support ECU assembly

·

CAN communication system


U0293 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication stop between power management control ECU and driving support ECU assembly or skid control ECU continues for 1 second or more
·

Power management control ECU

·

Driving support ECU assembly

·

Brake booster with master cylinder (skid control ECU)

·

CAN communication system


U1104 While dynamic radar cruise control is either preparing for operation or operating and power switch is on (IG), communication stop between driving support ECU assembly and millimeter wave radar sensor assembly, power management control ECU, or brake booster with master cylinder (skid control ECU) continues for 1 second or more
·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly

·

Power management control ECU

·

Brake booster with master cylinder (skid control ECU)

·

Wire harness or connector (Driving support ECU assembly - millimeter wave radar sensor assembly)

·

CAN communication system



PROCEDURE

1.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check for DTCs.


Result:
Result Proceed to
DTC U1104 is output (for Radar Cruise) A
DTC U1104 is output (for Hybrid Control) A
DTCs other than U1104 are output B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

2.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).


Result:
Result Proceed to
CAN communication is normal A
CAN communication is malfunctioning B



A

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the driving support ECU assembly and millimeter wave radar sensor assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-38 (LRRD) - A2-4 (LRRD) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L60-38 (LRRD) or A2-4 (LRRD) - Body ground Always 10 kΩ or higher



c.

Reconnect the driving support ECU assembly and millimeter wave radar sensor assembly connectors.



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
U191234E02
1.302,1.917 0.99,2.719 false 0.417,0.292 0.615,0.469 0.198,0.177 10 false *a 0.354,1.052 0.646,1.219 0.292,0.167 10 false L60 0.844,2.74 1.198,2.885 0.354,0.146 10 false GND

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L60-25 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Reconnect the driving support ECU assembly connector.



OK

5.REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

5.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support control ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

6.CHECK FOR DTCs (DTC U1104)
6.CHECK FOR DTCs (DTC U1104)
a.

Connect the GTS to DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.


Result:
Result Proceed to
DTC is not output A
DTC U1104 is output B



A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY