Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The millimeter wave radar sensor assembly and driving support ECU assembly transmit data for general vehicle control and diagnosis functions using communication lines. The millimeter wave radar sensor assembly transmits information about the vehicle in front to the driving support ECU assembly.

DTC No. DTC Detection Condition Trouble Area
U0235 The ECM detects a communication error signal (from the millimeter wave radar sensor assembly to the driving support ECU assembly) for 1 second or more while the dynamic radar cruise control is operating
·

Millimeter wave radar sensor circuit

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

E230012E01
1.169,0.584 1.588,0.735 0.419,0.151 10 LRRD 1.169,0.883 1.588,1.034 0.419,0.151 10 LRDD 1.318,1.21 1.589,1.361 0.271,0.151 10 IGB 1.169,1.518 1.588,1.669 0.419,0.151 10 SGND 5.582,0.575 6.001,0.726 0.419,0.151 10 LRRD 5.582,0.874 6.001,1.025 0.419,0.151 10 LRDD 5.582,1.201 5.720,1.352 0.138,0.151 10 B 5.582,1.509 6.001,1.660 0.419,0.151 10 GND 1.676,0.475 1.804,0.659 0.128,0.184 10 4 1.683,0.783 1.811,0.967 0.128,0.184 10 3 1.683,1.106 1.811,1.289 0.128,0.184 10 5 1.683,1.421 1.811,1.605 0.128,0.184 10 2 2.714,4.114 2.842,4.298 0.128,0.184 10 2 5.301,0.485 5.490,0.668 0.189,0.184 10 38 5.312,0.793 5.501,0.976 0.189,0.184 10 16 5.312,1.115 5.501,1.299 0.189,0.184 10 30 5.312,1.43 5.501,1.614 0.189,0.184 10 25 5.224,2.12 5.484,2.276 0.260,0.156 10 L60 0.475,2.095 0.735,2.250 0.260,0.156 10 A2 5.518,2.12 6.508,2.470 0.989,0.350 10 Driving Support ECU Assembly 4.601,2.305 5.167,2.617 0.566,0.312 10 ECU-IG No. 2 0.727,2.095 2.209,2.473 1.482,0.378 10 Millimeter Wave Radar Sensor Assembly 1.354,3.257 1.817,3.441 0.464,0.184 10 DC/DC 3.341,3.771 3.953,3.955 0.612,0.184 10 IG1 No. 1 2.907,4.229 3.322,4.412 0.415,0.184 10 IG1D 0.937,3.851 1.332,4.034 0.396,0.184 10 MAIN 2.527,4.591 2.809,4.733 0.282,0.142 10 L6 2.76,4.591 4.064,4.941 1.304,0.350 10 Power Management Control ECU 1.036,4.978 1.650,5.289 0.614,0.311 10 Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
U111382E03
2.167,2.24 2.448,2.927 false 0.281,0.229 0.594,0.479 0.313,0.25 10 false *a 0.531,1.5 0.719,1.677 0.188,0.177 10 false A2 2.375,2.948 2.646,3.146 0.271,0.198 10 false IGB

Disconnect the millimeter wave radar sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A2-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


d.

Reconnect the millimeter wave radar sensor assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - IG1 RELAY)

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the driving support ECU assembly and millimeter wave radar sensor assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-16 (LRDD) - A2-3 (LRDD) Always Below 1 Ω
L60-30 (B) - A2-5 (IGB) Always Below 1 Ω
L60-25 (GND) - A2-2 (SGND) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L60-16 (LRDD) or A2-3 (LRDD) - Body ground Always 10 kΩ or higher
L60-30 (B) or A2-3 (LRDD) - Body ground Always 10 kΩ or higher



c.

Reconnect the driving support ECU assembly and millimeter wave radar sensor assembly connectors.



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
U111383E03
1.552,2.25 1.844,2.938 false 0.271,0.323 0.583,0.573 0.313,0.25 10 false *a 0.521,1.51 0.708,1.688 0.188,0.177 10 false A2 1.729,2.958 2.156,3.156 0.427,0.198 10 false SGND

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A2-2 (SGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Reconnect the millimeter wave radar sensor assembly connector.



OK

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.
U191228E02
1.76,2.219 2.115,2.906 false 0.219,0.167 0.531,0.417 0.313,0.25 10 false *a 0.51,1.5 0.698,1.677 0.188,0.177 10 false A2 1.969,2.938 2.396,3.135 0.427,0.198 10 false LRDD

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A2-3 (LRDD) - Body ground Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

NG

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).


b.

Adjust the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

6.CHECK FOR DTCs (DTC U0235)
6.CHECK FOR DTCs (DTC U0235)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC U0235 is output B




A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY