Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A40  ENG / EHV Device  


DESCRIPTION

When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the power management control ECU or ECM via CAN communication, DTC C1A40 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A40 While power switch is on (IG), hybrid control system or SFI system malfunction signal is detected for 1 second or more while the dynamic radar cruise control is operating
·

Hybrid control system

·

Power management control ECU

·

SFI system

·

ECM

·

Driving support ECU assembly



WIRING DIAGRAM

E230010E01
1.291,0.608 1.739,0.778 0.448,0.170 10 CANH 1.305,1.113 1.753,1.282 0.448,0.170 10 CANL 5.537,0.608 5.984,0.778 0.448,0.170 10 CA2H 5.537,1.113 5.984,1.282 0.448,0.170 10 CA2L 3.93,0.608 4.378,0.778 0.448,0.170 10 CA2H 3.93,1.113 4.378,1.282 0.448,0.170 10 CA2L 2.976,0.608 3.424,0.778 0.448,0.170 10 CA1H 2.976,1.113 3.424,1.282 0.448,0.170 10 CA1L 1.789,0.426 1.986,0.582 0.198,0.156 10 13 1.789,0.917 1.924,1.072 0.135,0.156 10 5 4.434,0.417 4.632,0.573 0.198,0.156 10 34 4.434,0.907 4.632,1.063 0.198,0.156 10 35 2.678,0.417 2.876,0.573 0.198,0.156 10 25 2.678,0.907 2.876,1.063 0.198,0.156 10 24 5.305,0.426 5.503,0.582 0.198,0.156 10 39 5.291,0.917 5.489,1.072 0.198,0.156 10 17 2.691,0.608 2.911,0.783 0.221,0.174 10 L6 2.688,1.113 2.909,1.287 0.221,0.174 10 L6 4.441,0.608 4.662,0.783 0.221,0.174 10 L5 4.441,1.113 4.662,1.287 0.221,0.174 10 L5 0.533,1.652 0.800,1.808 0.267,0.156 10 A57 0.84,1.652 1.177,1.822 0.336,0.170 10 ECM 3.05,1.694 4.331,2.128 1.281,0.434 10 Power Management Control ECU 5.382,1.64 5.640,1.824 0.258,0.184 10 L60 5.659,1.64 7.007,2.001 1.348,0.360 10 Driving Support ECU Assembly 0.864,2.297 2.664,2.439 1.799,0.142 10 : CAN Communication Line

PROCEDURE

1.CHECK FOR DTC (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK FOR DTC (SFI SYSTEM)

B

2.CHECK FOR DTC (SFI SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

3.CHECK FOR DTCs (DTC C1A40)

B

3.CHECK FOR DTCs (DTC C1A40)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A40 is output B




A

END

B

4.REPLACE POWER MANAGEMENT CONTROL ECU
4.REPLACE POWER MANAGEMENT CONTROL ECU
a.

Replace the power management control ECU (See page Power Source / Network>POWER DISTRIBUTION>POWER MANAGEMENT CONTROL ECU>REMOVAL).



NEXT

5.CHECK FOR DTCs (DTC C1A40)
5.CHECK FOR DTCs (DTC C1A40)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A40 is output B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

NEXT

7.CHECK FOR DTCs (DTC C1A40)
7.CHECK FOR DTCs (DTC C1A40)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A40 is output B




A

END

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY