Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2015.08–2016.05
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301643 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  C1AAA  FCM Destination Information Uninitialized  


DESCRIPTION

When the lane departure warning camera is replaced with a new one, it acquires the country specification information from the main body ECU (multiplex network body ECU). If the lane departure warning camera cannot store the country specification information, DTC C1AAA is stored.

DTC Code DTC Detection Condition Trouble Area
C1AAA While the power switch is on (IG), the lane departure warning camera cannot store the country specification information.
·

Main body ECU (multiplex network body ECU)

·

Lane departure warning camera



CAUTION / NOTICE / HINT

NOTICE:
·

When the lane departure warning camera is replaced with a new one, adjustment of the lane departure warning camera axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT).

·

When replacing the lane departure warning camera, always replace it with a new one. If a lane departure warning camera which was installed to another vehicle is used, the information stored in the lane departure warning camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

The lane departure alert system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshooting the lane departure alert system after confirming that the communication systems are functioning properly.



PROCEDURE

1.READ VALUE USING GTS (DESTINATION INFORMATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Lane Departure Alert / Data List.


e.

Read the Data List according to the display on the GTS.

Lane Departure Alert
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Destination Information Status of the country/JPN, NA, EURO, CHINA or OTHER (GEN-EXP) Actual country code -


Result:
Result Proceed to
Country specification information for vehicle and lane departure warning camera match A
Country specification information for vehicle and lane departure warning camera do not match B



A

2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

B

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
2.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AAA is not output A
DTC C1AAA is output B



A

B

3.REPLACE LANE DEPARTURE WARNING CAMERA
3.REPLACE LANE DEPARTURE WARNING CAMERA
a.

Replace the lane departure warning camera with a new one (See page Engine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>REMOVAL).


b.

Perform the lane departure warning camera adjustment (See page Engine / Hybrid System>CRUISE CONTROL>LANE RECOGNITION CAMERA SENSOR>ADJUSTMENT).



NEXT

4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
4.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AAA is not output A
DTC C1AAA is output B



A

END (LANE DEPARTURE WARNING CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) with a new one (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

6.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
6.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AAA is not output A
DTC C1AAA is output B



A

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE))

B