Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › from 2016.05
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2304  Open or Short Circuit in U Phase  C2305  Open or Short Circuit in V Phase  C2306  Open or Short Circuit in W Phase  


DESCRIPTION

The shift control actuator assembly consists of a parking lock motor and rotation angle sensor. The transmission control ECU assembly receives a P position switch signal from the hybrid vehicle control ECU and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The transmission control ECU assembly stores these DTCs when it detects a malfunction in the parking lock motor system.

DTC No. DTC Detection Condition Trouble Area
C2304 With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage of transmission control ECU assembly terminal MUA is 6 V or less for 1 second or more.
·

Auxiliary battery

·

Transmission control ECU assembly

·

Shift control actuator assembly

·

P CON MTR relay (Transaxle parking lock control relay)

·

Wire harness or connector


C2305 With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage of transmission control ECU assembly terminal MVA is 6 V or less for 1 second or more.
C2306 With the power switch on (IG) (auxiliary battery voltage is 8 V or more), voltage of transmission control ECU assembly terminal MWA is 6 V or less for 1 second or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove/install the auxiliary battery or disconnect the cable from the negative (-) auxiliary battery terminal before instructed.

·

It may not be possible to clear the following DTCs using the GTS: DTC C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). In such cases, disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs after the repair.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK DTC OUTPUT (TRANSMISSION CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTCs C2304, C2305 and C2306 are detected simultaneously A
Only DTC C2304, C2305 or C2306 is detected B


HINT:
·

If DTCs C2304, 2305 and 2306 are stored at the same time, there may be a malfunction in the parking lock motor (BMA signal) power source circuit.

·

If DTC C2304, 2305 or 2306 is stored individually, there may be a malfunction in the parking lock motor (MUA, MVA or MWA signal) circuits.




e.

Turn the power switch off.



A

2.CHECK FREEZE FRAME DATA

B

6.READ VALUE USING GTS (U, V, W VOLTAGE)
2.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


d.

Read the freeze frame data of DTCs C2304, C2305 and C2306.

Result:
Result Proceed to
IG (+B) voltage is 9 V or more A
IG (+B) voltage is less than 9 V B



e.

Turn the power switch off.



A

3.CLEAR DTC

B

7.CLEAR DTC
4.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.



NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
5.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Release the brake pedal and turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and move the shift lever to select neutral (N).


d.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
DTC C2304, 2305 or 2306 is output A
DTC C2304, 2305 or 2306 is not output. B



f.

Turn the power switch off.



A

6.READ VALUE USING GTS (U, V, W VOLTAGE)

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)

6.READ VALUE USING GTS (U, V, W VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Data List / U Phase Voltage Value, V Phase Voltage Value, W Phase Voltage Value.


d.

Read the data list displayed on the GTS.

Result:
Tester Display Condition Specified Condition
U Phase Voltage Value Power switch on (IG) 9 to 14 V
V Phase Voltage Value Power switch on (IG) 9 to 14 V
W Phase Voltage Value Power switch on (IG) 9 to 14 V



e.

Turn the power switch off.



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR ASSEMBLY)
7.CLEAR DTC
a.

Turn the power switch on (IG).


b.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


c.

Read and record the DTCs and freeze frame data.


d.

Turn the power switch off.


e.

Disconnect the P CON MAIN fuse and wait for at least 60 seconds.


f.

Check for DTCs again to see if the DTCs are cleared.



NEXT

8.INSPECT AUXILIARY BATTERY
8.INSPECT AUXILIARY BATTERY
a.

Inspect the auxiliary battery (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

Result:
Result Proceed to
Charge or replace the auxiliary battery. A
The auxiliary battery voltage is normal. B




A

9.CHARGE OR REPLACE AUXILIARY BATTERY

B

4.CHARGE AUXILIARY BATTERY
9.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>COMPONENTS).



NEXT

5.CHECK DTC OUTPUT (SIMULATION TEST)
10.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR ASSEMBLY)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Disconnect the D2 shift control actuator assembly connector.


c.
U154759E03
1.25,1.135 0.833,1.135 true 1.417,1.073 0.854,0.438 true 1.99,1.073 2.656,0.406 true 1.344,3.458 0.802,2.854 true 1.396,3.781 0.927,4.24 true 1.594,3.771 2.063,4.25 true 0.104,0.135 0.385,0.323 0.281,0.188 10 false *a 0.104,2.438 0.385,2.625 0.281,0.188 10 false *b 0.427,1.063 0.802,1.24 0.375,0.177 10 false MWA 2.708,0.281 3.083,0.458 0.375,0.177 10 false MUA 0.531,0.25 0.906,0.427 0.375,0.177 10 false MVA 1.958,4.271 2.333,4.448 0.375,0.177 10 false MWA 0.448,2.708 0.823,2.885 0.375,0.177 10 false MUA 0.583,4.167 0.958,4.344 0.375,0.177 10 false MVA 1.646,0.219 1.938,0.385 0.292,0.167 10 false A23 1.688,2.615 2.052,2.781 0.365,0.167 10 false D2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A23-5 (MUA) - D2-1 (MUA) Power switch off Below 1 Ω
A23-2 (MVA) - D2-6 (MVA) Power switch off Below 1 Ω
A23-1 (MWA) - D2-7 (MWA) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-5 (MUA) or D2-1 (MUA) - Body ground and other terminals Power switch off 10 kΩ or higher
A23-2 (MVA) or D2-6 (MVA) - Body ground and other terminals Power switch off 10 kΩ or higher
A23-1 (MWA) or D2-7 (MWA) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Front view of wire harness connector
(to Shift Control Actuator Assembly)


d.

Connect the D2 shift control actuator assembly connector.


e.

Connect the A23 transmission control ECU assembly connector.



OK

11.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)
a.

Disconnect the D2 shift control actuator assembly connector.


b.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


c.
C351646E01
0.563,0.948 0.896,1.177 0.333,0.229 1.594,0.896 1.385,0.438 true 0.094,0.104 0.5,0.365 0.406,0.26 10 false *a 1.177,0.229 1.583,0.49 0.406,0.26 10 false BMA 0.646,0.969 1.052,1.229 0.406,0.26 10 false D2 0.125,1.844 0.531,2.104 0.406,0.26 10 false *1 2.229,1.885 2.635,2.146 0.406,0.26 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D2-2 (BMA) - 5 (P CON MTR relay) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D2-2 (BMA) or 5 (P CON MTR relay) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)
*b P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Relay Block and Junction Block Assembly


d.

Reinstall the P CON MTR relay (transaxle parking lock control relay).


e.

Connect the D2 shift control actuator assembly connector.



OK

12.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


c.
C351647E01
2.552,0.917 2.938,1.177 0.385,0.26 2.135,0.833 2.406,0.385 true 1.698,0.823 1.49,0.385 true 1.125,0.802 1.479,0.896 true 0.135,0.146 0.688,0.469 0.552,0.323 10 false *a 0.729,0.698 1.281,1.021 0.552,0.323 10 false MWA 1.302,0.208 1.854,0.531 0.552,0.323 10 false MVA 2.26,0.208 2.813,0.531 0.552,0.323 10 false MUA 2.438,1.927 2.99,2.25 0.552,0.323 10 false *b 0.229,1.885 0.781,2.208 0.552,0.323 10 false *1 2.625,0.958 3.177,1.281 0.552,0.323 10 false A23

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A23-5 (MUA) - 5 (P CON MTR relay) Power switch off Below 50 Ω
A23-2 (MVA) - 5 (P CON MTR relay) Power switch off Below 50 Ω
A23-1 (MWA) - 5 (P CON MTR relay) Power switch off Below 50 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-5 (MUA) - Body ground Power switch off 10 kΩ or higher
A23-2 (MVA) - Body ground Power switch off 10 kΩ or higher
A23-1 (MWA) - Body ground Power switch off 10 kΩ or higher
5 (P CON MTR relay) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Relay Block and Junction Block Assembly


d.

Reinstall the P CON MTR relay (transaxle parking lock control relay).


e.

Connect the A23 transmission control ECU assembly connector.



OK

13.INSPECT P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)

NG

13.INSPECT P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)

OK

14.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)

NG

REPLACE P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)

14.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


c.
C351647E02
1.708,0.125 2.094,0.385 0.385,0.26 2.271,1.26 2.615,1.198 false 0.135,0.146 0.688,0.469 0.552,0.323 10 false *a 2.677,1.094 3.229,1.417 0.552,0.323 10 false BMA 2.438,1.927 2.99,2.25 0.552,0.323 10 false *b 0.229,1.885 0.781,2.208 0.552,0.323 10 false *1 1.771,0.177 2.323,0.5 0.552,0.323 10 false A23

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A23-23 (BMA) - 2 (P CON MTR relay) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-23 (BMA) or 2 (P CON MTR relay) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Relay Block and Junction Block Assembly


d.

Reinstall the P CON MTR relay (transaxle parking lock control relay).


e.

Connect the A23 transmission control ECU assembly connector.



OK

15.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY - BODY GROUND)
a.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


b.
C226006E07
2.302,0.156 2.615,0.375 0.313,0.219 10 false *a 0.115,0.063 0.344,0.302 0.229,0.24 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (P CON MTR relay) - Body ground Power switch off Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Relay Block and Junction Block Assembly


c.

Reinstall the P CON MTR relay (transaxle parking lock control relay).



OK

16.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT)
a.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


b.
C226006E07
2.302,0.156 2.615,0.375 0.313,0.219 10 false *a 0.115,0.063 0.344,0.302 0.229,0.24 10 false *1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (P CON MTR relay) - Body ground Always 9 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a P CON MTR Relay (transaxle parking lock control relay) Connector of Engine Room Relay Block and Junction Block Assembly


c.

Reinstall the P CON MTR relay (transaxle parking lock control relay).



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

CHECK AND REPAIR POWER SOURCE CIRCUIT