Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › 2014.11–2016.05
RM2070E _52 Drivetrain _061917 AXLE AND DIFFERENTIAL _0301659 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE FRONT WHEEL

Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the front flexible hose.



Hide 43512 5.REMOVE FRONT DISC

Hide 43502D 6.REMOVE FRONT AXLE HUB BOLT

a.
C211927E04
1.563,1.365 0.917,1.365 false 2.094,0.979 2.094,0.594 2.094,0.594 2.854,0.594 false 2.417,1.135 2.417,0.594 false 0.604,1.281 0.906,1.427 0.302,0.146 10 true SST 2.854,0.5 3.042,0.656 0.188,0.156 10 false *1

Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Text in Illustration
*1 Service Nut

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.

SST
09628-10011  

NOTICE:

Do not damage the threads of the front axle hub bolts.



Hide 43502D 7.INSTALL FRONT AXLE HUB BOLT

a.
C211928E06
0.969,0.458 1.24,0.26 1.24,0.26 1.458,0.26 false 0.656,0.938 0.656,1.542 false 1.427,0.177 1.615,0.365 0.188,0.188 10 true *1 0.583,1.552 0.75,1.698 0.167,0.146 10 false *2

Install a washer and service nut to a new front axle hub bolt as shown in the illustration.

Text in Illustration
*1 Service Nut
*2 Washer

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



b.

Using a screwdriver or an equivalent tool to hold the front axle hub, install the hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




c.

Remove the 3 service nuts and washer from the 3 front axle hub bolts.


Hide 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing the front disc brake caliper assembly.



Hide 10.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>INSTALLATION).


b.

Connect the reservoir level switch connector.