Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › from 2016.05
RM2070E _53 Suspension _061919 FRONT SUSPENSION _0301667 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48158C 1.INSTALL FRONT LOWER COIL SPRING INSULATOR

a.
C320548E03
2.125,1.406 2.708,1.844 2.708,1.844 2.917,1.844 false 1.896,3.24 1.51,2.531 1.51,2.531 1.396,2.531 false 2.281,3.354 2.281,3.49 2.281,3.49 3.031,3.49 false 2.396,3.094 2.396,3.365 false 1.938,3.573 1.781,3.573 1.781,3.573 1.781,4.177 false 1.979,3.802 1.781,3.802 false 2.948,1.771 3.135,1.979 0.188,0.208 10 false *a 3.042,3.396 3.302,3.635 0.26,0.24 10 false *c 1.208,2.427 1.469,2.667 0.26,0.24 10 false *c 1.698,4.198 1.958,4.438 0.26,0.24 10 false *b

Install the front lower coil spring insulator to the front shock absorber assembly.

Text in Illustration
*a Positioning Pin
*b Depression
*c Claw

NOTICE:
·

When installing the front lower coil spring insulator, fit the insulator to the depression of the spring seat and insert the positioning pin into the hole.

·

When installing the front lower coil spring insulator, make sure that the front lower coil spring insulator does not get caught on the claws of the front shock absorber assembly.




Hide 48331C 2.INSTALL FRONT SPRING BUMPER

a.
C355609

Install the front spring bumper to the front shock absorber assembly.

NOTICE:

Face the smaller diameter end of the front spring bumper downward.



Hide 48132 3.INSTALL FRONT COIL SPRING

a.
C265532E01
2.348,1.522 2.348,1.126 2.348,1.126 2.609,1.126 false 2.63,1.033 2.940,1.193 0.310,0.160 10 SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C275706E01
0.303,0.096 0.473,0.257 0.170,0.161 10 *a 0.303,2.566 0.473,2.726 0.170,0.160 10 *b

Attach the arm of SST to the diameter of the front coil spring.

Text in Illustration
*a Correct
*b Incorrect

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




c.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench. It will damage SST.




d.
C265533E06
1.573,0.229 2.5,0.229 true 0.719,1.573 0.719,1.729 false 1.344,0.135 0.823,0.135 false 2.521,0.146 2.698,0.302 0.177,0.156 10 false *b 0.635,0.052 0.813,0.208 0.177,0.156 10 false *a 0.573,1.75 0.885,1.906 0.313,0.156 10 false SST

Install the front coil spring to the front shock absorber assembly.

Text in Illustration
*a Paint Mark
*b Paint Mark (blue)

NOTICE:
·

Make sure that the end of the front coil spring is positioned in the depression of the front lower spring seat.

·

Make sure to install the coil spring to the front shock absorber assembly so that the paint mark (blue) will be positioned at the lower side of the vehicle.




Hide 48045A 4.INSTALL FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C331760E02
2.396,1.167 2.99,1.333 2.99,1.333 3.094,1.333 false 2.344,1.219 2.979,1.854 2.979,1.854 3.083,1.854 false 3.104,1.25 3.354,1.469 0.25,0.219 10 false *1 3.104,1.813 3.354,2.031 0.25,0.219 10 false *a

Install the front spring seat sub-assembly with insulator to the front shock absorber assembly.

Text in Illustration
*1 Front Upper Coil Spring Seat
*a Top End of the Insulator (Shock Absorber Dust Cover)

NOTICE:

Make sure that the top end of the insulator (shock absorber dust cover) and the front upper coil spring seat are securely attached.



Hide 48619A 5.INSTALL STRUT MOUNTING BEARING

a.
C207004E04
1.135,0.318 1.297,0.462 0.162,0.144 10 *a 1.144,0.913 1.327,1.065 0.184,0.152 10 *b

Install the strut mounting bearing.

Text in Illustration
*a Upper Side
*b Lower Side

NOTICE:

Do not install the bearing upside down.



Hide 48609 6.INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Install the front suspension support sub-assembly to the front shock absorber assembly.

NOTICE:

When installing, align the cutout on the front suspension support sub-assembly and the shock absorber piston rod end.



Hide 48609E 7.TEMPORARILY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C373155

Install the collar to the front shock absorber assembly.


b.

Temporarily tighten a new front support to front shock absorber nut.


c.

Remove SST from the front coil spring.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48045A 8.CONNECT FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C339774E01
0.787,1.331 0.28,1.439 0.28,1.439 0.217,1.439 false 0.038,1.35 0.250,1.520 0.211,0.170 10 *1 1.254,1.685 1.466,1.855 0.211,0.170 10 *a 0.894,1.23 1.33,1.666 1.33,1.666 1.535,1.279 false

Engage the end of the insulator of the front spring seat sub-assembly with insulator with the claws of the front shock absorber assembly.

Text in Illustration
*1 Front Spring Seat Sub-assembly with Insulator
*a Claw

NOTICE:
·

Make sure that the end of the insulator is securely attached to the claws of the front shock absorber assembly.

·

Make sure there is no excessive damage to the bellows of the insulator.

·

Do not allow oil, grease, etc., to contact the insulator.

·

If there is oil or grease on the insulator, remove it with a cloth. Do not use an alcohol based cleaner.




Hide 9.INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Install the front shock absorber with coil spring (upper side) with the 3 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 bolts and 2 nuts.

Torque:
240 N*m (2447 kgf*cm, 177 ft.*lbf)

NOTICE:

While keeping the bolts from rotating, tighten the nuts.



Hide 48609E 10.FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.

Fully tighten the front support to front shock absorber nut.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 48684B 11.INSTALL FRONT SUSPENSION SUPPORT DUST COVER

a.
C241365

Install the front suspension support dust cover.


Hide 89543 12.INSTALL FRONT SPEED SENSOR

a.

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not twist the front speed sensor when installing it.


HINT:

Install the front flexible hose first and then the speed sensor harness bracket.



Hide 48810 13.INSTALL FRONT STABILIZER LINK ASSEMBLY

a.

Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.


Hide 55701J 14.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 15.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55736D 16.INSTALL COWL BODY MOUNTING REINFORCEMENT LH (for LHD)

Hide 55735C 17.INSTALL COWL BODY MOUNTING REINFORCEMENT RH (for RHD)

Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 20.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT