44785C
1.INSTALL BRAKE BOOSTER GASKET
Install a new brake booster gasket to the brake booster with master cylinder assembly.
47210L
2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Install the brake booster with master cylinder assembly with the 4 nuts.
| *1 | Connector Portion |
| *2 | Union |
| *3 | Push Rod Clevis |
| *4 | Boot |
| *5 | Front No. 2 Brake Tube |
Do not kink or damage the brake lines.
Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.
Be careful not to allow brake fluid to enter the connector of ECU.
If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.
Engage the grommet of the brake line.
Set the brake line to the clamp as shown in the illustration.
| *1 | Clamp |
| *2 | Brake Line |
Securely install the brake line so that it contacts the clamp as shown in the illustration.
Using a union nut wrench, connect the brake line to the front flexible hose RH.
Do not kink or damage the brake lines.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Using a union nut wrench, connect each brake line to the brake booster with master cylinder assembly as shown in the illustration.
| *1 | Clamp |
| *2 | Brake Line |
| *a | to Front Wheel Cylinder LH |
| *b | to Rear Wheel Cylinder RH |
| *c | to Brake Booster Pump Assembly |
| *d | to Rear Wheel Cylinder LH |
| *e | to Front Wheel Cylinder RH |
Do not kink or damage the brake lines.
Securely install the brake line so that it contacts the clamp as shown in the illustration.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Install the wire harness clamp bracket to the brake booster with master cylinder assembly with the bolt.
| *a | Stopper |
Securely install the wire harness clamp bracket so that its stopper contacts the brake booster with master cylinder assembly as shown in the illustration.
Connect the connector.
Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.
Make sure that the connector lock is locked securely.
Engage the clamp.
47234L
3.CONNECT NO. 1 RESERVOIR HOSE
Connect the No. 1 reservoir hose, No. 2 reservoir hose and No. 2 brake actuator hose to the brake booster with master cylinder assembly and No. 1 brake actuator tube with the 3 clips.
| *1 | No. 1 Reservoir Hose |
| *2 | No. 2 Reservoir Hose |
| *3 | No. 2 Brake Actuator Hose |
|
Up |
Make sure to match the identification marks on the hoses, brake booster with master cylinder assembly and brake actuator tube.
| Hose Identification Mark Color | Connection Color | |
|---|---|---|
| No. 1 Reservoir Hose | White | White (Unpainted) |
| No. 2 Reservoir Hose | Green | Green |
| No. 2 Brake Actuator Hose | Yellow | Yellow |
When connecting the reservoir hose, face the identification mark up.
Make sure to install the hose to the proper location.
Install the clip within the range as shown in the illustration.
47235G
4.CONNECT NO. 2 RESERVOIR HOSE
44572
5.CONNECT NO. 2 BRAKE ACTUATOR HOSE
44551
6.BLEED NO. 1 BRAKE ACTUATOR TUBE
Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air enters into the brake booster pump assembly and it may cause the brake booster pump assembly to be damaged.
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.
SAE J1703 or FMVSS No. 116 DOT3
Install the brake master cylinder reservoir filler cap assembly.
Remove the nut, disengage the clamp and separate the No. 1 brake actuator tube from the vehicle body.
Lift up the brake master cylinder reservoir with bracket as far as possible.
Do not spill the brake fluid.
While holding the brake master cylinder reservoir with bracket, twist and hold the No. 1 brake actuator tube 90° toward the vehicle front, and wait at 5 seconds.*1
Do not damage the hoses.
Keeping the No. 1 brake actuator tube twisted causes the remaining air inside the No. 1 brake actuator tube to be expelled to the brake master cylinder reservoir assembly.
Return the No. 1 brake actuator tube to its original state.
While holding the brake master cylinder reservoir with bracket, twist and hold the No. 1 brake actuator tube 90° toward the vehicle rear, and wait at 5 seconds.
Do not damage the hoses.
Keeping the No. 1 brake actuator tube twisted causes the remaining air inside the No. 1 brake actuator tube to be expelled to the brake master cylinder reservoir assembly.
Return the No. 1 brake actuator tube to its original state.*2
Repeat steps *1 to *2, 5 times.
While holding the brake master cylinder reservoir with bracket, pinch the brake actuator hose 10 times with your fingers.
Do not use pliers or similar to pinch the brake actuator hose. Doing so may cause damage to the brake actuator hose. Make sure to use your fingers.
Repeat steps *1 to *2, 5 times again, and check that air is not expelled from the No. 1 brake actuator tube.
Engage the clamp and install the No. 1 brake actuator tube with the nut.
7.INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET
Install the brake master cylinder reservoir with bracket with the 2 nuts.
Engage the clamp.
47264A
8.INSTALL PUSH ROD PIN
9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45260
10.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
11.INSTALL COLUMN HOLE COVER SILENCER SHEET
47101A
12.INSTALL BRAKE PEDAL RETURN SPRING
13.FILL RESERVOIR WITH BRAKE FLUID
14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
15.BLEED BRAKE SYSTEM
16.INSPECT AND ADJUST BRAKE PEDAL
17. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR
After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).
55701J
18.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
Install the outer cowl top panel sub-assembly with the 9 bolts.
Bend the water guard plate RH and engage the claw.
Bend the No. 1 heater air duct splash shield seal and engage the claw.
Engage the 2 clamps to install the wire harness to the outer cowl top panel sub-assembly.
Engage the clamp to install the wire harness to the outer cowl top panel sub-assembly.
55735C
19.INSTALL COWL BODY MOUNTING REINFORCEMENT RH
Install the cowl body mounting reinforcement RH with the 3 bolts.
20.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55606
21.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY