Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM › 2012.03–2013.08
RM2070E _53 Suspension _061920 REAR SUSPENSION _0301675 REAR AXLE BEAM A

REAR SUSPENSION  REAR AXLE BEAM  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE REAR WHEELS

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 57627A 5.REMOVE REAR FLOOR SIDE MEMBER COVER RH

a.
C259564

Remove the 3 bolts.


b.

Disengage the 3 clips and remove the rear floor side member cover RH.


Hide 53605F 6.REMOVE REAR SUSPENSION BRACE SUB-ASSEMBLY

a.

for Type A:

i.

Remove the 4 bolts.

C236508


ii.

Disengage the clip and remove the rear suspension brace sub-assembly.



b.

for Type B:

i.

Remove the 4 bolts and the rear suspension brace sub-assembly.

C308462



Hide 89516D 7.DISCONNECT SKID CONTROL SENSOR WIRE LH

Hide 89516C 8.DISCONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89516D 9.SEPARATE SKID CONTROL SENSOR WIRE LH

Hide 89516C 10.SEPARATE SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as for the LH side.


Hide 47316A 11.SEPARATE REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)

a.
C236529

Using a union nut wrench, separate the rear brake tube flexible hose from the No. 4 brake tube.

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.




b.

Remove the bolt and separate the rear brake tube flexible hose from the rear axle beam assembly.


Hide 47316A 12.SEPARATE REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)

a.
C226105

Using a union nut wrench, separate the rear brake tube flexible hose from the No. 3 brake tube.

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.




b.

Remove the clip and separate the rear brake tube flexible hose from the rear axle beam assembly.


Hide 13.REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH

a.
C236550

Using a union nut wrench, separate the No. 4 brake tube while holding the rear flexible hose LH with a wrench.

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting points.




b.
C236537

Remove the clip and separate the rear flexible hose LH.


c.

Remove the 2 bolts and rear disc brake caliper assembly LH with rear flexible hose LH.


Hide 14.REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 42491 15.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Remove the 2 parking brake shoe adjusting hole plugs.


Hide 42431 16.REMOVE REAR DISC (for LH Side)

Hide 42431 17.REMOVE REAR DISC (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 47324 18.REMOVE REAR NO. 4 BRAKE TUBE

a.
C155135

Remove the nut and rear No. 4 brake tube from the rear axle beam assembly.


Hide 47323 19.REMOVE REAR NO. 3 BRAKE TUBE

HINT:

Perform the same procedure as for the rear No. 4 brake tube.


Hide 42450B 20.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 21.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 22.SEPARATE PARKING BRAKE ASSEMBLY (for LH Side)

a.
C236524

Remove the bolt and separate the No. 3 parking brake cable assembly from the rear axle beam assembly.


b.
C236509

Remove the nut and separate the parking brake assembly from the rear axle beam assembly.

NOTICE:

Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable.



Hide 23.SEPARATE PARKING BRAKE ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 65638 24.SEPARATE REAR WHEEL HOUSE LINER LH

Hide 65637 25.SEPARATE REAR WHEEL HOUSE LINER RH

HINT:

Perform the same procedure as for the LH side.


Hide 89407A 26.SEPARATE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 48231B 27.REMOVE REAR COIL SPRING LH

Hide 48231A 28.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48259A 29.REMOVE REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 30.REMOVE REAR UPPER COIL SPRING INSULATOR RH

Hide 48258C 31.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 32.REMOVE REAR LOWER COIL SPRING INSULATOR RH

Hide 42110F 33.REMOVE REAR AXLE BEAM ASSEMBLY

a.

Support the rear axle beam assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools to replicate standard vehicle height conditions as shown in the illustration.

C207252E06
4.938,2.083 4.938,2.271 false 1.99,1.75 1.99,2 1.99,2 2.135,2 false 2.74,1.76 2.74,1.906 false 4.521,1.74 4.521,1.906 false 5.24,1.75 5.24,1.979 5.24,1.979 5.073,1.979 false 4.875,2.281 5.052,2.438 0.177,0.156 10 false *1 2.146,1.917 2.323,2.073 0.177,0.156 10 false *2 2.677,1.906 2.854,2.073 0.177,0.167 10 false *3 4.448,1.917 4.625,2.083 0.177,0.167 10 false *3 4.906,1.906 5.083,2.063 0.177,0.156 10 false *2 1.76,1.521 2,1.677 0.24,0.156 10 true (A) 0.344,1.771 0.583,1.927 0.24,0.156 10 false (B) 5.26,1.49 5.469,1.677 0.208,0.188 10 true (A) 6.667,1.76 6.917,1.917 0.25,0.156 10 false (B)

Text in Illustration
*1 Engine Lifter *2 Wooden Block
*3 Attachment - -

NOTICE:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Remove the 2 bolts (A) and 2 nuts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Since the stopper nuts are used, turn the bolts.



c.

Remove the 2 bolts (B) and rear axle beam assembly.


Hide 48725G 34.REMOVE REAR AXLE CARRIER BUSHING LH

a.
C159021E16
2.094,1.375 1.844,1.635 1.844,1.635 1.292,1.635 true 1.083,1.552 1.292,1.76 0.208,0.208 10 true *a

Put a matchmark on the rear axle beam assembly so that the mark aligns with the arrow mark on the rear axle carrier bushing LH. (If the rear axle beam assembly is reused.)

Text in Illustration
*a Matchmark


b.

Using a chisel and hammer, bend the 2 ribs on the rear axle carrier bushing LH.

C370356E01
2.833,2.333 1.833,2.333 1.833,2.333 1.833,1.75 true 1.26,2.417 1.802,2.583 1.802,2.583 1.323,1.896 true 2,2.333 2,1.583 true 2.115,2.333 2.115,1.542 true 2.188,2.333 2.188,1.5 true 2.26,0.229 2.573,0.427 0.313,0.198 10 false *c 3.302,1.229 3.615,1.427 0.313,0.198 10 false *b 2.885,2.24 3.323,2.458 0.438,0.219 10 false SST 1.854,2.521 2.167,2.719 0.313,0.198 10 false *a

Text in Illustration
*a Bend Portion
*b Turn
*c Hold

NOTICE:

When removing the rear axle carrier bushing, do not erase the matchmark on the rear axle beam assembly.



c.

Using SST, remove the rear axle carrier bushing LH from the rear axle beam assembly.

SST
09710-26011  (09710-05061)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010  (09951-00530)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.



Hide 48725F 35.REMOVE REAR AXLE CARRIER BUSHING RH

HINT:

Perform the same procedure as for the LH side.