Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD) › 2012.03–2014.11
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301696 BRAKE BOOSTER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. DISABLE BRAKE CONTROL

a.

Wait at least 2 minutes after turning the power switch off.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.
C256204

Disconnect the reservoir level switch connector with the parking brake applied.


c.

Disconnect the cable from the negative (-) auxiliary battery terminal (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>REMOVAL).


d.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


e.

Check that the brake pedal can not be further depressed.


f.

Release the parking brake.


Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

a.
C256205

Remove the 3 bolts and cowl body mounting reinforcement LH.


Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C256192

Disengage the clamp of the wire harness.


b.
C256206

Disengage the claw and bend the No. 1 heater air duct splash shield seal.


c.
C256207

Disengage the claw and bend the water guard plate RH.


d.
C256191

Remove the 9 bolts and outer cowl top panel sub-assembly.


Hide 7.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47101A 8.REMOVE BRAKE PEDAL RETURN SPRING

Hide 10.SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

a.
C238469

Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.


Hide 47234L 11.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C238470E03
2,0.917 2.438,0.917 true 1.292,1.375 0.896,1.375 true 2.438,0.813 2.667,1.01 0.229,0.198 10 true *1 0.708,1.292 0.896,1.469 0.188,0.177 10 true *2

Move the 2 clips and disconnect the No. 1 reservoir hose and No. 2 reservoir hose from the brake booster with master cylinder assembly.

Text in Illustration
*1 No. 1 Reservoir Hose
*2 No. 2 Reservoir Hose


Hide 47235G 12.DISCONNECT NO. 2 RESERVOIR HOSE

Hide 44571 13.DISCONNECT BRAKE ACTUATOR HOSE

a.
C205677

Move the clip and disconnect the brake actuator hose from the brake booster pump assembly.


Hide 14.REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

Hide 44595 15.REMOVE NO. 5 BRAKE ACTUATOR BRACKET

a.
C205680

Disengage the clamp.


b.

Remove the 2 nuts and No. 5 brake actuator bracket.


Hide 47210L 16.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C225908

Release the lock lever and disconnect the connector.

NOTICE:

Be careful not to allow the brake fluid to enter the removed connector.



b.
C205681

Remove the 2 bolts and No. 2 brake tube clamp bracket from the brake booster with master cylinder assembly.


c.
C205682E05
1.677,0.427 1.917,0.177 1.917,0.177 2,0.177 true 1.948,0.719 1.406,0.719 true 1.938,0.927 1.167,0.927 true 1.938,1.177 1.938,1.604 true 2.052,0.594 2.5,0.594 true 2.5,0.51 2.688,0.688 0.188,0.177 10 true *a 1.229,0.625 1.417,0.802 0.188,0.177 10 true *b 0.979,0.844 1.167,1.01 0.188,0.167 10 true *c 1.844,1.604 2.031,1.771 0.188,0.167 10 true *d 2,0.094 2.167,0.24 0.167,0.146 10 false *e

Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


d.

Use tags or make a memo to identify the places to reconnect.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


e.
C205683

Disengage the 2 clamps to separate the brake line from the vehicle body.


f.
C238462E01
2.304,2.667 2.471,2.821 0.167,0.154 10 *1 0.514,2.725 0.682,2.879 0.167,0.154 10 *2 2.976,2.849 3.143,3.003 0.167,0.154 10 *3 2.771,3.754 2.938,3.908 0.167,0.154 10 *4 0.641,4.013 0.808,4.167 0.167,0.154 10 *5 1.853,2.753 2.304,2.753 false 1.716,3.305 0.7,2.818 0.7,2.818 1.277,3.421 false 1.386,3.856 0.827,4.095 0.827,4.095 1.267,4.119 false 2.727,3.195 2.811,2.927 2.811,2.927 2.976,2.927 false 2.426,3.567 2.6,3.834 2.6,3.834 2.77,3.834 false

Remove the 4 nuts and brake booster with master cylinder assembly.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.




Hide 44785C 17.REMOVE BRAKE BOOSTER GASKET