Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2016.05–2020.08
RM2070E _53 Suspension _061921 TIRE PRESSURE MONITORING _0301678 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU and receiver detects any problems, the tire pressure warning light blinks for 1 minute then illuminates, and tire pressure monitoring is disabled at the same time. At this time, the ECU stores a DTC in memory.

Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink to output DTCs.

The tire pressure warning ECU and receiver sends the tire pressure warning light illumination request signal to the main body ECU (multiplex network body ECU) via a direct line. The main body ECU (multiplex network body ECU) then sends the signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C249402E12
3.385,0.74 3.792,0.958 0.406,0.219 10 false RDA 3.813,0.635 4.104,0.896 0.292,0.26 10 false 16 5.323,0.74 5.729,0.906 0.406,0.167 10 false RDA 5.115,0.635 5.281,0.802 0.167,0.167 10 false 4 5.188,2.656 6.042,2.823 0.854,0.167 10 false R42 5.188,2.823 6.958,3.26 1.771,0.438 10 false Tire Pressure Warning ECU and Receiver 1.448,1.74 3.333,1.958 1.885,0.219 10 false Combination Meter Assembly 1.24,0.469 1.563,0.635 0.323,0.167 10 false L201 1.594,0.469 3.26,0.896 1.667,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.448,2.031 3.333,2.25 1.885,0.219 10 false - Tire Pressure Warning Light 0.625,3.313 2.448,3.531 1.823,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check if CAN communication system DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM for with Central Gateway ECU, Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM for without Central Gateway ECU).

Result:
Result Proceed to
DTCs are not output. A
DTCs are output (w/ Central Gateway ECU). B
DTCs are output (w/o Central Gateway ECU). C




A

2.CHECK DTC OUTPUT (B1247)

B

C

2.CHECK DTC OUTPUT (B1247)

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1247 is not output.




OK

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

NG

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light using the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON -

OK:

The tire pressure warning light turns on or off in accordance with the GTS operation.




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG