The skid control ECU inputs the stop light switch signal and detects the brake pedal operation status.
The skid control ECU has an open detection circuit, which outputs this DTC if it detects an open in the stop light input line or ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1249/49 | 231 | When IG1 terminal voltage is 9.5 V or more, an open stop light switch circuit continues for 10 seconds or more. | ·
Wire harness or connector ·
Stop light switch ·
Brake booster with master cylinder (Skid control ECU) |
When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | ON |
| Brake pedal released | OFF |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Check that the stop light switch display observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
OK
NG
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC (C1249/49) is not output | A |
| DTC (C1249/49) is output (for LHD) | B |
| DTC (C1249/49) is output (for RHD) | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Check the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).
The stop light switch is normal.
OK
NG
Reconnect the stop light switch connector.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-33 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V |
| A58-33 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG
Reconnect the skid control ECU connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Turn the power switch on (ready).
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC (C1249/49) is not output | A |
| DTC (C1249/49) is output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
If the lighting system is normal but the DTC is still output, replace the brake booster with master cylinder (skid control ECU) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL for LHD, Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL for RHD).
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the power switch off (lock).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-33 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V |
| A58-33 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B
C