Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.11–2015.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1246/46  Master Cylinder Pressure Sensor Malfunction  C1281/81  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  C1364/61  Wheel Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The regulator pressure sensor and the wheel cylinder pressure sensor are built into the brake actuator, and measure the regulator pressure and the wheel cylinder pressure sent to the skid control ECU.

DTC C1281/81 will be cleared when the regulator pressure sensor sends a regulator pressure signal or when Test Mode ends. DTC C1281/81 is output only in Test Mode.

DTC Code INF Code DTC Detection Condition Trouble Area
C1246/46 201 Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds. Brake booster with master cylinder (Skid control ECU or brake actuator)
↑ 202 Regulator pressure sensor output voltage (Preg) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. ↑
↑ 203 When not under braking, the regulator pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 3 seconds or more. ↑
↑ 204 Either of the following is detected:
1.

The regulator pressure sensor output voltage does not correspond with stroke sensor and the readings remain out of specification for 0.5 to 5 seconds or more continuously.

(The stroke sensor may be malfunctioning.)

2.

The regulator pressure sensor output voltage does not correspond with wheel cylinder pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.

(May be output with INF code 424.)


·

Brake pedal stroke sensor

·

Brake booster with master cylinder (Skid control ECU or brake actuator)


↑ 207 Fluctuation of regulator pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. Brake booster with master cylinder (Skid control ECU or brake actuator)
C1364/61 421 Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more. Brake booster with master cylinder (Skid control ECU or brake actuator)
↑ 422 Wheel cylinder pressure sensor output voltage (Pfront) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. ↑
↑ 423 When not under braking, the wheel cylinder pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 0.1 to 3 seconds or more. ↑
↑ 424 The wheel cylinder pressure sensor output voltage does not correspond with regulator pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.
(May be output with INF code 204.)
↑
↑ 426 Fluctuation of wheel cylinder pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. ↑
C1281/81 - Detected only during Test Mode.
·

Stop light switch

·

Regulator pressure sensor



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU or brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK STOP LIGHT SWITCH INSTALLATION
a.

Check the protrusion of the rod (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).

OK:

Stop light switch is installed properly.


HINT:

If the stop light switch is not installed properly, adjust the protrusion of the rod before proceeding to the next step.




OK

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)

NG

2.READ VALUE USING GTS (REGULATOR PRESSURE SENSOR)
a.

Set a pedal effort gauge and LSPV gauge to the rear wheel (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Regulator Pressure Sensor Output Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


e.

Check the output value of the regulator pressure sensor as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi))
100 (10, 22.5) 1.50 to 2.30 4.88 to 8.88 (49.8 to 90.5, 708 to 1288) 4.88 to 8.88 (49.8 to 90.5, 708 to 1288)
200 (20, 45.0) 3.37 to 4.17 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612) 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612)


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

3.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)
a.

Set a LSPV gauge to the front wheel (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


c.

Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure during electronically controlled brake system control.

Standard Voltage:
for Front Wheel Cylinder Pressure Sensor LH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94

for Front Wheel Cylinder Pressure Sensor RH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR AND PRESSURE SENSOR COMPARISON)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR AND PRESSURE SENSOR COMPARISON)
a.

Set a pedal effort gauge and LSPV gauge to the front and rear wheels (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).


b.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor2 Brake pedal stroke sensor 2 / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Regulator Pressure Sensor Output Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


c.

Check the output value of the brake pedal stroke sensor as the brake pedal is depressed.

Standard Voltage:
Brake Effort
(N (kgf, lbf))
Stroke Sensor
(V)
Stroke Sensor2
(V)
Regulator Pressure Sensor Output
(V)
Wheel Cylinder Pressure Sensor
(V)
100 (10, 22.5) 1.26 to 1.96 3.04 to 3.74 1.50 to 2.30 1.30 to 2.10
200 (20, 45.0) 1.74 to 2.44 2.56 to 3.26 3.37 to 4.17 2.89 to 3.69


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

5.RECONFIRM DTC

B

C

5.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Perform a road test.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1246/46 and C1364/61) are not output A
DTCs (C1246/46 and/or C1364/61) are output (for LHD) B
DTCs (C1246/46 and/or C1364/61) are output (for RHD) C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER