The regulator pressure sensor and the wheel cylinder pressure sensor are built into the brake actuator, and measure the regulator pressure and the wheel cylinder pressure sent to the skid control ECU.
DTC C1281/81 will be cleared when the regulator pressure sensor sends a regulator pressure signal or when Test Mode ends. DTC C1281/81 is output only in Test Mode.
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1246/46 | 201 | Sensor supply voltage (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 202 | Regulator pressure sensor output voltage (Preg) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. | ↑ |
| ↑ | 203 | When not under braking, the regulator pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 3 seconds or more. | ↑ |
| ↑ | 204 | Either of the following is detected:
1.
The regulator pressure sensor output voltage does not correspond with stroke sensor and the readings remain out of specification for 0.5 to 5 seconds or more continuously. (The stroke sensor may be malfunctioning.) 2.
The regulator pressure sensor output voltage does not correspond with wheel cylinder pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously. (May be output with INF code 424.) |
·
Brake pedal stroke sensor ·
Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 207 | Fluctuation of regulator pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| C1364/61 | 421 | Sensor supply voltage 1 (VCM1) is 4.75 V or less, or 5.25 V or more for 0.05 seconds or more. | Brake booster with master cylinder (Skid control ECU or brake actuator) |
| ↑ | 422 | Wheel cylinder pressure sensor output voltage (Pfront) is less than 8%, or 90.3% or more (less than 0.4 V, or 4.52 V or more) of sensor supply voltage (VCM1) for 0.05 seconds or more. | ↑ |
| ↑ | 423 | When not under braking, the wheel cylinder pressure sensor output voltage is 0.2 V or less or 0.88 V or more for 0.1 to 3 seconds or more. | ↑ |
| ↑ | 424 | The wheel cylinder pressure sensor output voltage does not correspond with regulator pressure sensor and the outputs remain out of specification for 0.5 to 5 seconds or more continuously.
(May be output with INF code 204.) |
↑ |
| ↑ | 426 | Fluctuation of wheel cylinder pressure sensor output is out of specification (the difference between the present value and last value is 15 MPa (153.0 kgf/cm2, 2176 psi) or more) for 0.1 seconds or more. | ↑ |
| C1281/81 | - | Detected only during Test Mode. | ·
Stop light switch ·
Regulator pressure sensor |
When replacing the brake booster with master cylinder (skid control ECU or brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
Check the protrusion of the rod (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).
Stop light switch is installed properly.
If the stop light switch is not installed properly, adjust the protrusion of the rod before proceeding to the next step.
OK
NG
Set a pedal effort gauge and LSPV gauge to the rear wheel (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Regulator Pressure Sensor Output | Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released:
0.10 to 0.90 V |
Reading increases when brake pedal is depressed |
Check the output value of the regulator pressure sensor as the brake pedal is depressed.
| Brake Effort
(N (kgf, lbf)) |
Regulator Pressure Sensor Output
(V) |
Rear Right Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
Rear Left Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
|---|---|---|---|
| 100 (10, 22.5) | 1.50 to 2.30 | 4.88 to 8.88 (49.8 to 90.5, 708 to 1288) | 4.88 to 8.88 (49.8 to 90.5, 708 to 1288) |
| 200 (20, 45.0) | 3.37 to 4.17 | 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612) | 14.01 to 18.01 (142.9 to 183.6, 2033 to 2612) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Set a LSPV gauge to the front wheel (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released:
0.10 to 0.90 V |
Reading increases when brake pedal is depressed |
Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure during electronically controlled brake system control.
| Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
Wheel Cylinder Pressure Sensor
(V) |
|---|---|
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
Wheel Cylinder Pressure Sensor
(V) |
|---|---|
| 2.0 (20.4, 290) | 0.53 to 1.33 |
| 5.0 (51.0, 725) | 1.12 to 1.92 |
| 7.0 (71.4, 1015) | 1.52 to 2.32 |
| 10.0 (102.0, 1451) | 2.14 to 2.94 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Set a pedal effort gauge and LSPV gauge to the front and rear wheels (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>ON-VEHICLE INSPECTION).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor 2 / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 3.65 to 4.35 V | Reading decreases when brake pedal is depressed |
| Regulator Pressure Sensor Output | Regulator pressure sensor output / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released:
0.10 to 0.90 V |
Reading increases when brake pedal is depressed |
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released:
0.10 to 0.90 V |
Reading increases when brake pedal is depressed |
Check the output value of the brake pedal stroke sensor as the brake pedal is depressed.
| Brake Effort
(N (kgf, lbf)) |
Stroke Sensor
(V) |
Stroke Sensor2
(V) |
Regulator Pressure Sensor Output
(V) |
Wheel Cylinder Pressure Sensor
(V) |
|---|---|---|---|---|
| 100 (10, 22.5) | 1.26 to 1.96 | 3.04 to 3.74 | 1.50 to 2.30 | 1.30 to 2.10 |
| 200 (20, 45.0) | 1.74 to 2.44 | 2.56 to 3.26 | 3.37 to 4.17 | 2.89 to 3.69 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Turn the power switch off (lock).
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
Perform a road test.
Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C1246/46 and C1364/61) are not output | A |
| DTCs (C1246/46 and/or C1364/61) are output (for LHD) | B |
| DTCs (C1246/46 and/or C1364/61) are output (for RHD) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C