Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2016.05–2020.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter sub-assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter sub-assembly and the skid control ECU.

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU is malfunctioning.


WIRING DIAGRAM

C209415E10
0.698,0.792 1.104,0.938 0.406,0.146 10 false CANL 0.677,1.323 1.083,1.469 0.406,0.146 10 false CANH 1.208,0.646 1.406,0.813 0.198,0.167 10 false 20 1.208,1.177 1.385,1.354 0.177,0.177 10 false 19 0.135,5.875 0.417,6.031 0.281,0.156 10 false L27 0.438,5.875 1.615,6.313 1.177,0.438 10 false Combination Meter Sub-assembly 1.917,1.875 3.354,2.094 1.438,0.219 10 false from IG1 NO. 1 Relay 4.24,2.031 5.229,2.198 0.99,0.167 10 false ECU-IG NO. 2 6.135,0.75 6.552,0.927 0.417,0.177 10 false CA1L 6.135,1.302 6.552,1.448 0.417,0.146 10 false CA1H 6.135,1.865 6.385,2.01 0.25,0.146 10 false IG1 6.135,2.396 6.552,2.542 0.417,0.146 10 false GND 5.885,5.896 7.083,6.25 1.198,0.354 10 false Brake Booster with Master Cylinder 6.135,2.906 6.552,3.052 0.417,0.146 10 false GND2 6.135,3.406 6.531,3.594 0.396,0.188 10 false GND3 6.135,3.906 6.573,4.083 0.438,0.177 10 false GND4 6.135,4.427 6.542,4.615 0.406,0.188 10 false GND5 6.135,4.948 6.542,5.135 0.406,0.188 10 false GND6 5.865,0.646 6.042,0.833 0.177,0.188 10 false 38 5.865,1.177 6.094,1.344 0.229,0.167 10 false 37 5.865,1.75 6.094,1.917 0.229,0.167 10 false 16 5.865,2.281 6.094,2.438 0.229,0.156 10 false 28 5.865,2.74 6.156,2.917 0.292,0.177 10 false 27 5.865,3.281 6.104,3.438 0.24,0.156 10 false 26 5.865,3.813 6.115,3.969 0.25,0.156 10 false 25 5.865,4.313 6.094,4.49 0.229,0.177 10 false 24 5.865,4.823 6.115,4.99 0.25,0.167 10 false 23 5.531,5.896 5.854,6.042 0.323,0.146 10 false A58

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM for with Central Gateway ECU or Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM for without Central Gateway ECU).

Result:
Result Proceed to
DTC is not output A
DTC is output (w/ Central Gateway ECU) B
DTC is output (w/o Central Gateway ECU) C




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

C

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V




OK

4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
a.
U154753E02
1.344,1.865 1.042,2.823 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.271,0.875 0.563,1.031 0.292,0.156 10 false A58 0.948,2.844 1.26,3 0.313,0.156 10 false IG1

Disconnect the skid control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

5.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.
U154749E02
2.26,1.802 2.26,1 false 2.365,1.802 2.708,0.667 false 2.146,1.802 1.802,0.667 false 2.469,1.802 3.01,0.979 false 2.052,1.802 1.5,0.979 false 2.646,1.99 2.938,2.76 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.271,0.865 0.563,1.021 0.292,0.156 10 false A58 2.031,0.802 2.438,0.958 0.406,0.156 10 false GND4 1.552,0.49 1.958,0.646 0.406,0.156 10 false GND5 2.49,0.49 2.896,0.646 0.406,0.156 10 false GND3 2.813,0.802 3.219,0.958 0.406,0.156 10 false GND2 1.25,0.802 1.656,0.958 0.406,0.156 10 false GND6 2.771,2.781 3.125,2.938 0.354,0.156 10 false GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-28 (GND) - Body ground Always Below 1 Ω
A58-27 (GND2) - Body ground Always Below 1 Ω
A58-26 (GND3) - Body ground Always Below 1 Ω
A58-25 (GND4) - Body ground Always Below 1 Ω
A58-24 (GND5) - Body ground Always Below 1 Ω
A58-23 (GND6) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

6.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.INSPECT COMBINATION METER SUB-ASSEMBLY
a.

Reconnect the skid control ECU connector.


b.

Perform the Active Test of the combination meter sub-assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter sub-assembly.

OK:

The ABS warning light turns on or off in accordance with the GTS operation.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (w/ Multi-information Display) C
NG (w/o Multi-information Display) D


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE COMBINATION METER SUB-ASSEMBLY

D