The accumulator pressure sensor is built into the actuator and detects the accumulator pressure.
The skid control ECU turns on the brake warning light / red (malfunction) and brake warning light / yellow (minor malfunction), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.
DTC C1256/56 may be output if the accumulator pressure drops due to frequent braking (this is not a malfunction).
| DTC Code | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1256/56 | 341 | Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.) |
·
Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction) ·
Pump motor malfunction ·
Accumulator deterioration ·
Accumulator pressure sensor ·
Supply voltage reduced |
Refer to DTCs C1252/52 and C1253/53 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1252/52).
When replacing the brake booster with master cylinder (brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).
When C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 are output together with C1256/56, inspect and repair the trouble areas indicated by C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1202/68, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1241/41, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1252/52, or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1391/69).
Ask the customer if frequent braking was performed while the brake warning light / yellow (minor malfunction) was on.
| Result | Proceed to |
|---|---|
| Frequent braking was not performed | A |
| Frequent braking was performed | B |
This DTC is output even if the accumulator pressure drops only temporarily due to frequent braking.
A
B
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the brake booster pump connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A17-1 (BM1) - A17-2 (GND1) | Always | Below 10 Ω |
| A18-2 (BM2) - A18-1 (GND2) | Always | Below 10 Ω |
| A17-1 (BM1) - A18-2 (BM2) | Always | Below 1 Ω |
| A17-2 (GND1) - A18-1 (GND2) | Always | Below 1 Ω |
| *a | Component without harness connected
(Brake Booster Pump) |
OK
NG
Reconnect the brake booster pump connectors.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Accumulator Sensor | Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V |
Specified value: 2.90 to 4.20 V | When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator |
Wait for 30 seconds without depressing the brake pedal.
Check that the accumulator pressure sensor output values change is within the specified range.
Accumulator pressure sensor output values change is within 0.55 V.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
The Active Test can be performed when the following conditions are met.
ABS main relay is on.
Park (P) is selected.
Parking brake is applied.
Vehicle speed is 0 km/h (0 mph).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ECB* Solenoid (SMC/SRC/SCC) | Switching solenoid valve (SMC/SRC/SCC) | Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
*: Electronically Controlled Brake System
Perform the Active Test of the solenoid using the GTS.
Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Wheel Cylinder Pressure Sensor | Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.10 to 0.90 V | Reading increases when brake pedal is depressed |
Check that the output value of the wheel cylinder does not increase.
The output value of the wheel cylinder does not increase.
If any output value increases, there may be brake fluid leaks in the brake actuator.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C