Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › 2014.11–2016.05
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301699 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster with master cylinder assembly.


Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C236042E01
2.434,2.68 2.584,2.830 0.150,0.150 10 *1 3.183,3.131 3.333,3.280 0.150,0.150 10 *3 2.888,3.645 3.037,3.794 0.150,0.150 10 *4 2.39,4.104 2.540,4.254 0.150,0.150 10 *5 0.476,2.822 0.626,2.971 0.150,0.150 10 *2 1.853,2.759 2.434,2.759 false 2.905,3.213 3.183,3.213 false 2.497,3.546 2.688,3.738 2.688,3.738 2.888,3.738 false 1.449,4.166 2.376,4.166 2.376,4.166 1.588,3.922 false 1.282,3.413 0.681,2.908 0.681,2.908 1.725,3.302 false

Install the brake booster with master cylinder assembly with the 4 nuts.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.

·

Be careful not to allow brake fluid to enter the connector of ECU.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.




b.

Engage the grommet of the brake line.


c.
C209150E01
3.08,1.424 3.236,1.571 0.156,0.147 10 *2 3.097,0.909 3.253,1.056 0.156,0.147 10 *1 2.846,1.507 3.08,1.507 false 2.955,1.001 3.097,1.001 false

Set the brake line to the clamp as shown in the illustration.

Text in Illustration
*1 Clamp
*2 Brake Line

NOTICE:

Securely install the brake line so that it contacts the clamp as shown in the illustration.



d.

Using a union nut wrench, connect the brake line to the front flexible hose RH.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




e.
C205652E05
1.042,0.823 0.896,0.573 0.896,0.573 0.792,0.573 true 1.146,1 1.333,0.573 1.333,0.573 1.396,0.573 true 1.135,1.469 1.135,1.823 1.135,1.823 1.063,1.823 true 1.781,0.865 1.938,0.615 1.938,0.615 1.979,0.615 true 1.156,1.292 1.583,1.292 true 2.969,1.094 3.125,1.094 false 2.854,1.625 3.031,1.625 false 0.615,0.479 0.813,0.708 0.198,0.229 10 true *a 1.406,0.479 1.667,0.729 0.26,0.25 10 true *b 1.583,1.208 1.802,1.458 0.219,0.25 10 true *c 2,0.531 2.25,0.76 0.25,0.229 10 true *e 3.135,1.01 3.292,1.167 0.156,0.156 10 false *1 3.063,1.542 3.219,1.698 0.156,0.156 10 false *2 0.885,1.74 1.042,1.896 0.156,0.156 10 true *d

Using a union nut wrench, connect each brake line to the brake booster with master cylinder assembly as shown in the illustration.

Text in Illustration
*1 Clamp
*2 Brake Line
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Securely install the brake line so that it contacts the clamp as shown in the illustration.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




f.
C205568E02
2.123,0.362 2.280,0.506 0.157,0.144 10 *a 1.715,0.443 2.123,0.443 false

Install the wire harness clamp bracket to the brake booster with master cylinder assembly with the bolt.

Text in Illustration
*a Stopper

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Securely install the wire harness clamp bracket so that its stopper contacts the brake booster with master cylinder assembly as shown in the illustration.



g.
C205566

Connect the connector.

NOTICE:
·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.

·

Make sure that the connector lock is locked securely.




h.

Engage the clamp.


Hide 47234L 3.CONNECT NO. 1 RESERVOIR HOSE

a.
C209163E03
1.375,3.385 1.792,3.385 true 0.927,3.656 0.927,4.073 true 2.396,3.76 2.396,4.177 true 1.813,3.302 2.021,3.521 0.208,0.219 10 true *1 0.823,4.073 1.031,4.25 0.208,0.177 10 true *2 2.323,4.198 2.5,4.365 0.177,0.167 10 true *3 0.708,0.958 1.021,1.115 0.313,0.156 10 false 120° 1.365,0.958 1.677,1.115 0.313,0.156 10 false 120° 0.906,1.792 1.135,1.948 0.229,0.156 10 false 60° 1.281,1.792 1.51,1.948 0.229,0.156 10 false 60° 2.521,0.948 2.75,1.104 0.229,0.156 10 false 30° 2.844,0.948 3.073,1.104 0.229,0.156 10 false 30° 0.385,0.74 0.552,0.885 0.167,0.146 10 false *1 1.323,0.74 1.49,0.885 0.167,0.146 10 false *2 2.458,0.74 2.625,0.885 0.167,0.146 10 false *3

Connect the No. 1 reservoir hose, No. 2 reservoir hose and No. 2 brake actuator hose to the brake booster with master cylinder assembly and No. 1 brake actuator tube with the 3 clips.

Text in Illustration
*1 No. 1 Reservoir Hose
*2 No. 2 Reservoir Hose
*3 No. 2 Brake Actuator Hose
V100136

Up

NOTICE:
·

Make sure to match the identification marks on the hoses, brake booster with master cylinder assembly and brake actuator tube.

Hose Identification Mark Color Connection Color
No. 1 Reservoir Hose White White (Unpainted)
No. 2 Reservoir Hose Green Green
No. 2 Brake Actuator Hose Yellow Yellow

·

When connecting the reservoir hose, face the identification mark up.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range as shown in the illustration.




Hide 47235G 4.CONNECT NO. 2 RESERVOIR HOSE

Hide 44572 5.CONNECT NO. 2 BRAKE ACTUATOR HOSE

Hide 44551 6.BLEED NO. 1 BRAKE ACTUATOR TUBE

NOTICE:

Make sure to bleed the air from the No. 1 brake actuator tube. If the air remains in the No. 1 brake actuator tube, the air enters into the brake booster pump assembly and it may cause the brake booster pump assembly to be damaged.


a.

Remove the brake master cylinder reservoir filler cap assembly.


b.

Add brake fluid into the reservoir between the MAX and MIN level on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3



c.

Install the brake master cylinder reservoir filler cap assembly.


d.
C295621

Remove the nut, disengage the clamp and separate the No. 1 brake actuator tube from the vehicle body.


e.
C295618

Lift up the brake master cylinder reservoir with bracket as far as possible.

NOTICE:

Do not spill the brake fluid.



f.
C295619

While holding the brake master cylinder reservoir with bracket, twist and hold the No. 1 brake actuator tube 90° toward the vehicle front, and wait at 5 seconds.*1

NOTICE:

Do not damage the hoses.


HINT:

Keeping the No. 1 brake actuator tube twisted causes the remaining air inside the No. 1 brake actuator tube to be expelled to the brake master cylinder reservoir assembly.



g.

Return the No. 1 brake actuator tube to its original state.


h.
C295620

While holding the brake master cylinder reservoir with bracket, twist and hold the No. 1 brake actuator tube 90° toward the vehicle rear, and wait at 5 seconds.

NOTICE:

Do not damage the hoses.


HINT:

Keeping the No. 1 brake actuator tube twisted causes the remaining air inside the No. 1 brake actuator tube to be expelled to the brake master cylinder reservoir assembly.



i.

Return the No. 1 brake actuator tube to its original state.*2


j.

Repeat steps *1 to *2, 5 times.


k.
C295617

While holding the brake master cylinder reservoir with bracket, pinch the brake actuator hose 10 times with your fingers.

NOTICE:

Do not use pliers or similar to pinch the brake actuator hose. Doing so may cause damage to the brake actuator hose. Make sure to use your fingers.



l.

Repeat steps *1 to *2, 5 times again, and check that air is not expelled from the No. 1 brake actuator tube.


m.
C295621

Engage the clamp and install the No. 1 brake actuator tube with the nut.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 7.INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

a.

Install the brake master cylinder reservoir with bracket with the 2 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Engage the clamp.


Hide 9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 10.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 11.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 47101A 12.INSTALL BRAKE PEDAL RETURN SPRING

Hide 13.FILL RESERVOIR WITH BRAKE FLUID

Hide 14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 16.INSPECT AND ADJUST BRAKE PEDAL

Hide 17. OBTAIN ZERO POINT OF YAW RATE AND ACCELERATION SENSOR

HINT:

After the brake booster with master cylinder assembly is replaced, obtain the zero point of the yaw rate and acceleration sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CALIBRATION).


Hide 55701J 18.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install the outer cowl top panel sub-assembly with the 9 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C236048

Bend the water guard plate RH and engage the claw.


c.
C236049

Bend the No. 1 heater air duct splash shield seal and engage the claw.


d.

Engage the 2 clamps to install the wire harness to the outer cowl top panel sub-assembly.


e.

Engage the clamp to install the wire harness to the outer cowl top panel sub-assembly.


Hide 55735C 19.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

a.

Install the cowl body mounting reinforcement RH with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 20.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55606 21.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY