47070
1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY
Install the brake booster pump assembly, 2 brake traction actuator bracket bushings and 2 brake actuator case collars to the brake actuator bracket assembly with the 2 nuts.
| *1 | Nut |
| *2 | Brake Actuator Case Collar |
| *3 | Brake Traction Actuator Bracket Bushing |
| *4 | Brake Actuator Bracket Assembly |
| *5 | Brake Booster Pump Assembly |
| *6 | Brake Actuator Bracket Cushion |
| *7 | Brake Booster Pump Collar |
| *8 | Brake Booster Pump Bushing |
Do not drop the brake booster pump assembly when carrying it.
Do not carry the brake booster pump assembly by the connector.
Confirm that the 2 brake actuator bracket cushions are on the brake actuator bracket assembly, and each brake booster pump bushing and brake booster pump collar are on the brake booster pump assembly when installing the brake booster pump assembly to the brake actuator bracket assembly.
Do not remove the hole plugs before installing a new brake booster pump assembly because the brake booster pump assembly is filled with brake fluid.
2.INSTALL BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET
Using SST, install the brake booster pump assembly with bracket with the 3 nuts.
Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
Tighten the 3 nuts in the order shown in the illustration.
Do not damage the fuel line, the brake lines or wire harness.
Use the formula to calculate special torque values for situations where SST is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Install the wire harness clamp and 2 fuel lines to the brake actuator bracket assembly.
| *1 | Wire Harness Clamp |
| *2 | Fuel Line |
| *3 | Front No. 4 Brake Tube |
Do not kink or damage the fuel lines.
Engage the clamp to install the front No. 4 brake tube to the brake actuator bracket assembly.
Do not kink or damage the brake line.
Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.
| *1 | No. 1 Brake Tube Clamp Bracket |
| *2 | No. 6 Brake Tube Clamp |
| *3 | No. 1 Front Brake Tube |
Using a union nut wrench, connect the front No. 1 brake tube to the brake booster pump assembly.
Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Install the No. 6 brake tube clamp to the No. 1 brake tube clamp bracket with the bolt.
Connect the No. 1 brake actuator hose to the brake booster pump assembly.
|
Front of Vehicle |
Make sure to match the identification mark on the hose with the brake booster pump rib.
Install the clip within the range as shown in the illustration.
Install the wire harness clamp.
Connect the 2 connectors.
44595
3.INSTALL NO. 5 BRAKE ACTUATOR BRACKET
Install the No. 5 brake actuator bracket with the 2 nuts.
Tighten the 2 nuts in the order shown in the illustration.
Install the wire harness clamp.
51201
4.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
5.SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET
44551
6.BLEED NO. 1 BRAKE ACTUATOR TUBE
7.INSTALL BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET
8.FILL RESERVOIR WITH BRAKE FLUID
9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
10.BLEED BRAKE SYSTEM
55701J
11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55735C
12.INSTALL COWL BODY MOUNTING REINFORCEMENT RH
13.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY