Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › 2012.03–2014.11
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301699 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 55606 4.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

a.
C205554

Remove the 3 bolts and cowl body mounting reinforcement RH.


Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
C236063

Disengage the clamp and separate the wire harness.


b.
C263237

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


c.
C236046

Disengage the claw and bend the No. 1 heater air duct splash shield seal.


d.
C236047

Disengage the claw and bend the water guard plate RH.


e.
C236050

Remove the 9 bolts and outer cowl top panel sub-assembly.


Hide 8.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately clean it off.


Hide 47101A 9.REMOVE BRAKE PEDAL RETURN SPRING

Hide 45259A 10.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 11.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 13.SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

a.
C236052

Disengage the clamp.


b.

Remove the 2 nuts and separate the brake master cylinder reservoir with bracket.


Hide 47234L 14.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C205564E02
1.375,0.896 1.865,0.896 true 0.906,1.177 0.906,1.604 true 2.385,1.281 2.385,1.615 false 1.875,0.802 2.094,1 0.219,0.198 10 true *1 0.833,1.615 1.042,1.802 0.208,0.188 10 true *2 2.313,1.625 2.531,1.833 0.219,0.208 10 true *3

Move the 3 clips and disconnect the No. 1 reservoir hose, No. 2 reservoir hose and No. 2 brake actuator hose from the brake booster with master cylinder assembly and No. 1 brake actuator tube.

Text in Illustration
*1 No. 1 Reservoir Hose
*2 No. 2 Reservoir Hose
*3 No. 2 Brake Actuator Hose


Hide 47235G 15.DISCONNECT NO. 2 RESERVOIR HOSE

Hide 44572 16.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

Hide 17.REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET

Hide 47210L 18.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C205565

Disengage the clamp.


b.

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

NOTICE:

Be careful not to allow the brake fluid to enter the removed connector.



c.
C205567

Remove the bolt and wire harness clamp bracket.


d.
C225899E03
1.042,0.813 0.885,0.646 0.885,0.646 0.698,0.646 true 1.135,1.01 1.427,0.646 1.427,0.646 1.51,0.646 true 1.135,1.292 1.531,1.292 true 1.125,1.49 1.125,1.875 true 1.792,0.875 1.885,0.719 1.885,0.719 2.292,0.719 true 0.51,0.552 0.729,0.823 0.219,0.271 10 true *a 1.531,0.563 1.781,0.771 0.25,0.208 10 true *b 1.552,1.198 1.813,1.417 0.26,0.219 10 true *c 1.042,1.875 1.198,2.021 0.156,0.146 10 false *d 2.302,0.635 2.542,0.854 0.24,0.219 10 true *e

Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


e.

Use tags or make a memo to identify the places to reconnect.

Text in Illustration
*a to Front Wheel Cylinder LH
*b to Rear Wheel Cylinder RH
*c to Brake Booster Pump Assembly
*d to Rear Wheel Cylinder LH
*e to Front Wheel Cylinder RH


f.
C211543

Using a union nut wrench, disconnect the brake line from the front flexible hose RH.


g.
C205653

Disengage the grommet and separate the brake line.


h.
C236042E01
2.434,2.68 2.584,2.830 0.150,0.150 10 *1 3.183,3.131 3.333,3.280 0.150,0.150 10 *3 2.888,3.645 3.037,3.794 0.150,0.150 10 *4 2.39,4.104 2.540,4.254 0.150,0.150 10 *5 0.476,2.822 0.626,2.971 0.150,0.150 10 *2 1.853,2.759 2.434,2.759 false 2.905,3.213 3.183,3.213 false 2.497,3.546 2.688,3.738 2.688,3.738 2.888,3.738 false 1.449,4.166 2.376,4.166 2.376,4.166 1.588,3.922 false 1.282,3.413 0.681,2.908 0.681,2.908 1.725,3.302 false

Remove the 4 nuts and brake booster with master cylinder assembly.

Text in Illustration
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.




Hide 44785C 19.REMOVE BRAKE BOOSTER GASKET