Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511/11  Torque Sensor 1 Malfunction  C1512/11  Torque Sensor 2 Malfunction  C1513/11  Torque Sensor Deviation Excessive  C1514/11  Torque Sensor Power Supply Voltage Malfunction  C1517/11  Torque Hold  


DESCRIPTION

The torque sensor converts the rotation torque input from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No. DTC Detection Condition Trouble Area
C1511/11 Torque sensor malfunction
·

Torque sensor (built into steering column assembly)

·

Power steering ECU assembly


C1512/11
C1513/11
C1514/11
C1517/11

WIRING DIAGRAM

C246147E01
4.806,3.72 6.795,3.941 1.989,0.221 10 Power Steering ECU Assembly 1.915,1.301 2.997,1.666 1.082,0.364 10 Torque Sensor 2.064,3.527 4.019,3.796 1.955,0.269 10 Steering Column Assembly 5.03,0.974 5.482,1.195 0.452,0.221 10 TRQ1 4.795,0.882 4.897,1.064 0.102,0.182 10 5 4.795,1.517 4.896,1.699 0.101,0.182 10 6 4.795,2.152 4.896,2.334 0.101,0.182 10 7 4.795,2.764 4.901,2.946 0.106,0.182 10 8 5.03,1.61 5.482,1.830 0.452,0.221 10 TRQV 5.03,2.249 5.482,2.470 0.452,0.221 10 TRQ2 5.03,2.884 5.482,3.105 0.452,0.221 10 TRQG 4.806,3.53 5.047,3.711 0.241,0.181 10 z14

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

If the steering column assembly has been replaced with a new one, perform rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
a.

Check the installation condition of the torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.




OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)

NG

CONNECT CONNECTOR

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
a.

Turn the power switch on (READY).


U154677E01
0.221,0.194 0.404,0.373 0.184,0.179 10 *a 1.338,2.934 1.764,3.073 0.427,0.139 10 TRQG 1.921,1.224 2.217,1.363 0.295,0.139 10 z14 2.073,2.934 2.478,3.073 0.406,0.139 10 TRQV 1.866,2.165 1.639,2.919 false 1.965,2.167 2.221,2.934 false 1.976,2.06 2.038,1.447 false

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z14-6 (TRQV) - z14-8 (TRQG) Power switch on (READY) 4.5 to 5.5 V


HINT:

If the voltage is as specified, take a note of the value.


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
U154678E02
1.844,2.167 1.104,2.917 false 2,2.167 2.26,2.938 false 1.896,2.167 1.792,2.917 false 2,2.021 2.167,1.458 false 0.198,0.156 0.385,0.323 0.188,0.167 10 false *a 0.844,2.938 1.271,3.073 0.427,0.135 10 false TRQG 2.052,1.24 2.333,1.375 0.281,0.135 10 false z14 1.563,2.938 1.948,3.073 0.385,0.135 10 false TRQ2 2.125,2.938 2.531,3.073 0.406,0.135 10 false TRQ1

Turn the power switch on (READY).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition (Steering Wheel Position) Specified Condition
z14-5 (TRQ1) - z14-8 (TRQG) Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to the right with vehicle stopped
2.5 to 3.8 V
Power switch on (READY)
Steering wheel being turned to the left with vehicle stopped
1.2 to 2.5 V
z14-7 (TRQ2) - z14-8 (TRQG) Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to the right with vehicle stopped
1.2 to 2.5 V
Power switch on (READY)
Steering wheel being turned to the left with vehicle stopped
2.5 to 3.8 V


Text in Illustration
*a Component with harness connected
(Power Steering ECU Assembly)


c.

Calculate the difference between the measured TRQV*1 and the sum of the output values of the torque sensor 1 and torque sensor 2.

HINT:

*1: TRQV was measured in the previous step.


OK:

0.3 V or less




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY