Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1522/24  Power Supply Sensor  C1523/24  Current Deviation Excessive  C1524/24  Motor Circuit Malfunction  C1555/25  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor through the motor circuit.

DTC No. DTC Detection Condition Trouble Area
C1522/24 Motor current sensor malfunction
·

Power steering motor (built into steering column assembly)

·

Power steering ECU assembly


C1523/24 Excessively large current deviation
C1524/24 Short (or open) in motor circuit or abnormal voltage or current in motor circuit
C1555/25 Motor relay circuit malfunction

WIRING DIAGRAM

C246148E17
4.573,2.604 4.844,2.771 0.271,0.167 10 false z16 4.573,2.771 6.635,2.938 2.063,0.167 10 false Power Steering ECU Assembly 0.198,2.479 2.208,3.177 2.01,0.698 10 false Power Steering Motor (built into Steering Column Assembly) 4.708,0.76 5,1.052 0.292,0.292 10 false V 4.708,1.354 4.969,1.573 0.26,0.219 10 false U 4.708,1.958 5.021,2.188 0.313,0.229 10 false W 4.49,0.625 4.594,0.875 0.104,0.25 10 false 1 4.49,1.24 4.615,1.469 0.125,0.229 10 false 2 4.49,1.813 4.594,2.042 0.104,0.229 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

If the steering column assembly has been replaced with a new one, perform rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).



PROCEDURE

1.READ VALUE USING GTS
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (READY).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the items "Motor Terminal Volt (U)", "Motor Terminal Volt (V)" and "Motor Terminal Volt (W)" in the Data List and read the value displayed on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Motor Terminal Volt (U) Motor terminal voltage (U phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Motor Terminal Volt (V) Motor terminal voltage (V phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Motor Terminal Volt (W) Motor terminal voltage (W phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned


Result
Result Proceed to
During steering operation, value changes within 4 to 35 V range A
During steering operation, voltage is not generated B


A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE STEERING COLUMN ASSEMBLY