Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1528/12  Motor Rotation Angle Sensor Malfunction  


DESCRIPTION

The motor rotation angle sensor detects the motor rotation angle and sends this information to the power steering ECU assembly.

DTC No. DTC Detection Condition Trouble Area
C1528/12 Motor rotation angle sensor malfunction
·

Motor rotation angle sensor (built into steering column assembly)

·

Power steering ECU assembly



WIRING DIAGRAM

C246149E10
4.281,0.74 4.688,0.885 0.406,0.146 10 false RZCS 4.281,1.573 4.688,1.719 0.406,0.146 10 false RZSN 4.281,2.448 4.594,2.594 0.313,0.146 10 false RZV 4.281,3.313 4.604,3.458 0.323,0.146 10 false RZG 4.25,4.063 6.333,4.229 2.083,0.167 10 false Power Steering ECU Assembly 4.25,3.927 4.594,4.094 0.344,0.167 10 false z15 0.323,3.958 2.781,4.656 2.458,0.698 10 false Motor Rotation Angle Sensor (built into Steering Column Assembly) 4.063,0.625 4.177,0.802 0.115,0.177 10 false 5 4.063,1.479 4.167,1.635 0.104,0.156 10 false 6 4.063,2.344 4.156,2.51 0.094,0.167 10 false 1 4.063,3.208 4.167,3.365 0.104,0.156 10 false 3 1.552,0.74 1.958,0.885 0.406,0.146 10 false RZCS 1.552,1.583 1.958,1.729 0.406,0.146 10 false RZSN 1.646,2.458 1.958,2.604 0.313,0.146 10 false RZV 1.635,3.313 1.958,3.458 0.323,0.146 10 false RZG

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced with a new one, perform assist map writing and rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

If the steering column assembly has been replaced with a new one, perform rotation angle sensor value initialization torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the installation condition of the motor rotation angle sensor connector.

OK:

Motor rotation angle sensor connector is securely connected to the power steering ECU assembly.




OK

2.READ VALUE USING GTS

NG

CONNECT CONNECTOR

2.READ VALUE USING GTS
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (READY).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item "Motor Rotation Angle" in the Data List and read the value displayed on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Motor Rotation Angle Motor rotation angle/
Min.: 0.000 deg
Max.: 1441.770 deg
During steering operation, motor rotation angle value changes from 0 to 360° Power switch on (READY) and steering wheel being turned

OK:

During steering operation, motor rotation angle value changes from 0 to 360°.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

3.CHECK STEERING COLUMN ASSEMBLY
3.CHECK STEERING COLUMN ASSEMBLY
a.
U154702E02
1.438,1.719 0.854,1.573 false 2.021,1.708 2.573,1.563 false 2.021,2.115 2.542,2.313 false 1.729,2.167 1.729,2.844 false 0.24,0.156 0.417,0.344 0.177,0.188 10 false *a 1.656,0.948 1.927,1.125 0.271,0.177 10 false z15 2.583,2.271 3,2.448 0.417,0.177 10 false RZSN 1.49,2.885 1.938,3.063 0.448,0.177 10 false RZCS 2.625,1.479 3.073,1.656 0.448,0.177 10 false RZG 0.49,1.469 0.813,1.646 0.323,0.177 10 false RZV

Disconnect the connector from the motor rotation angle sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z15-6 (RZSN) - z15-3 (RZG) Always 75.2 to 112.8 Ω
z15-1 (RZV) - z15-3 (RZG) Always 27.6 to 41.4 Ω
z15-5 (RZCS) - z15-3 (RZG) Always 73.2 to 110.8 Ω


Text in Illustration
*a Front view of wire harness connector
(to Motor Rotation Angle Sensor)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE STEERING COLUMN ASSEMBLY