Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM2070E _55 Steering _061930 STEERING GEAR / LINKAGE _0301718 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.SECURE STEERING WHEEL

a.
C237798

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 4.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C152549E13
1.406,0.479 1.417,0.115 1.417,0.115 1.531,0.115 false 2.219,2.375 2.219,2.865 2.219,2.865 2.115,2.865 false 2.948,0.427 2.74,0.24 2.74,0.24 2.49,0.24 false 0.938,3.052 1.354,3.052 true 1.906,2.781 2.083,2.948 0.177,0.167 10 false *1 1.552,0.031 1.729,0.208 0.177,0.177 10 false *2 2.292,0.156 2.479,0.313 0.188,0.156 10 false *a 1.375,2.969 1.583,3.125 0.208,0.156 10 false *a

Remove clip A, detach clip B from the body and disconnect the No. 1 steering column hole cover sub-assembly.

Text in Illustration
*1 Clip A
*2 Clip B
*a Lip

NOTICE:

Do not damage clips A and B.



Hide 6.REMOVE FRONT WHEELS

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442E 8.REMOVE NO. 2 ENGINE UNDER COVER

Hide 51442A 9.REMOVE FRONT NO. 3 ENGINE UNDER COVER

Hide 51444A 10.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 11.REMOVE REAR ENGINE UNDER COVER RH

Hide 48810 12.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 13.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 14.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and nut.


b.
C171770E01
2.481,0.919 2.789,1.081 0.309,0.163 10 SST 2.29,1.294 2.29,1.004 2.29,1.004 2.468,1.004 false

Install SST to the tie rod end.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper end of the tie rod end and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



d.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle.

C236256E01
1.025,0.621 1.438,0.208 1.438,0.208 2.007,0.208 false 2.017,0.123 2.193,0.279 0.176,0.156 10 *a 6.645,0.691 6.812,0.841 0.167,0.151 10 *b 6.644,0.345 6.811,0.495 0.167,0.151 10 *b 6.146,2.205 6.146,2.305 false 6.064,2.308 6.231,2.458 0.167,0.151 10 *c 3.747,2.08 3.747,2.289 false 3.613,2.293 3.902,2.449 0.289,0.156 10 SST 1.705,1.736 1.837,1.911 0.132,0.175 10 A 1.705,1.947 1.837,2.122 0.132,0.175 10 B 0.94,2.169 0.94,2.454 0.94,2.454 0.805,2.454 false 0.635,2.379 0.811,2.535 0.176,0.156 10 *1

Text in Illustration
*1 Center Nut - -
*a String *b Grease Application Area
*c Place the wrench here. - -

SST
09960-20010  (09961-02010)

NOTICE:
·

Apply grease to the bolt threads and the tip of SST.

·

Install SST with the center nut so that A and B shown in the illustration are parallel. Otherwise, the dust cover may be damaged.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle.




Hide 45046 15.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 16.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51425A 18.REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

Hide 51108A 19.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 20.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52258A 21.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 22.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 23.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 45025D 24.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C219383

Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.


Hide 45221 25.REMOVE STEERING INTERMEDIATE SHAFT

a.
C219384E01
1.88,1.355 2.553,1.355 false 1.861,1.262 2.285,1.262 2.285,1.262 2.285,1.355 false 2.571,1.258 2.732,1.419 0.161,0.162 10 *a

Put matchmarks on the steering intermediate shaft and steering link assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt and steering intermediate shaft from the steering link assembly.


Hide 26.REMOVE STEERING LINK ASSEMBLY

a.
C152552

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Keep the nut from rotating while turning the bolt because the nut has its own stopper.



Hide 27.SECURE STEERING LINK ASSEMBLY

a.
C153102E14
1.74,1.094 2,1.354 2,1.354 2.167,1.354 false 1.5,0.615 1.5,0.26 1.5,0.26 1.344,0.26 false 0.979,0.188 1.292,0.333 0.313,0.146 10 false SST 2.167,1.271 2.333,1.427 0.167,0.156 10 false *1

Using SST, secure the steering link assembly in a vise.

Text in Illustration
*1 Protective Tape

SST
09612-00012  

HINT:

Tape SST before use.



Hide 45047 28.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
C187022E13
1.592,1.469 1.783,1.625 0.191,0.156 10 *a 0.991,1.202 0.991,1.553 0.991,1.553 1.58,1.553 false 1.369,1.203 1.369,1.553 false

Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.

Text in Illustration
*a Matchmark


b.

Remove the tie rod end sub-assembly LH and lock nut.


Hide 45046 29.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.