1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
2. SECURE STEERING WHEEL
45259A
3.REMOVE COLUMN HOLE COVER SILENCER SHEET
45260
4.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45025D
5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
6.REMOVE FRONT WHEELS
52618A
7.REMOVE FRONT LOWER BUMPER ABSORBER
51441
8.REMOVE NO. 1 ENGINE UNDER COVER
51442E
9.REMOVE NO. 2 ENGINE UNDER COVER
51442A
10.REMOVE FRONT NO. 3 ENGINE UNDER COVER
51444A
11.REMOVE REAR ENGINE UNDER COVER LH
51443C
12.REMOVE REAR ENGINE UNDER COVER RH
48810
13.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.
If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.
48820B
14.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45047
15.SEPARATE TIE ROD END SUB-ASSEMBLY LH
45046
16.SEPARATE TIE ROD END SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
17.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
18.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
51425A
19.REMOVE FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT
Remove the 2 bolts and front engine mounting bracket lower reinforcement.
51108A
20.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH
Remove the 4 bolts and rear side rail reinforcement sub-assembly LH.
51107A
21.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
52258A
22.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH
Remove the 3 bolts and front suspension member rear brace LH.
52257
23.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH
Perform the same procedure as for the LH side.
51201
24.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 2 bolts and 2 wiring harness clamp brackets from the front suspension crossmember sub-assembly.
Remove the 2 bolts and 2 nuts, and separate the front suspension crossmember sub-assembly from the rear engine mounting insulator.
Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
| *1 | Engine Lifter |
| *2 | Attachment |
|
Attachment Placement Location |
Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
Use the attachments to keep the front suspension crossmember sub-assembly level.
The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.
Remove the 2 bolts and front suspension crossmember sub-assembly.
Slowly lower the front suspension crossmember sub-assembly.
When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.
57104E
25.REMOVE FRONT CROSS MEMBER SUB-ASSEMBLY
Using a jack, support the engine and transaxle assembly.
Remove the 2 bolts and separate the front cross member sub-assembly from the front engine mounting insulator.
Remove the 4 bolts and front cross member sub-assembly.
26.REMOVE STEERING LINK ASSEMBLY
48069
27.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.
|
Bolt |
|
Nut |
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48068
28.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
52256
29.REMOVE FRONT SUSPENSION MEMBER FRONT BRACE LH
52255
30.REMOVE FRONT SUSPENSION MEMBER FRONT BRACE RH
Perform the same procedure as for the LH side.
48811
31.REMOVE FRONT STABILIZER BAR
Remove the front stabilizer bar with 2 front stabilizer bar bushings from the front suspension crossmember sub-assembly.