Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2016.05–2017.12
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15F7  Certification ECU Vehicle Information Reading/Writing Process Malfunction  


DESCRIPTION

This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the audio and visual system vehicle customization screen.

HINT:

The certification ECU (smart key ECU assembly) controls the entry and start system related items that are customizable via the audio and visual system vehicle customization screen.


DTC No. DTC Detection Condition Trouble Area
B15F7 Certification ECU (smart key ECU assembly) vehicle setting processing malfunction
·

CAN communication system

·

Entry and start system (for Entry Function)

·

Entry and start system (for Start Function)

·

Certification ECU (smart key ECU assembly)

·

Radio and display receiver assembly



CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

CAN communication DTCs are not output.




OK

2.CHECK ENTRY AND START SYSTEM (for Entry Function)

NG

2.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check if the entry and start system (for Entry Function) is malfunctioning (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:

Customization may not be possible depending on the malfunction in the entry and start system (for Entry Function).


OK:

No malfunctions are present in the entry and start system (for Entry Function).




OK

3.CHECK ENTRY AND START SYSTEM (for Start Function)

NG

3.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check if the entry and start system (for Start Function) is malfunctioning (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:

Customization may not be possible depending on the malfunction in the entry and start system (for Start Function).


OK:

No malfunctions are present in the entry and start system (for Start Function).




OK

4.CHECK CUSTOMIZE ITEMS

NG

4.CHECK CUSTOMIZE ITEMS
a.

Make a note of the customizable items for each certification ECU (smart key ECU assembly) related system.

HINT:

The items shown as customizable via the audio and visual system vehicle customization screen can also be changed manually. In the following step, change the items manually.


i.

Check the customize parameters list for the entry and start system (for Entry Function) related items that can be customized via the audio and visual system vehicle customization screen (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).


ii.

Check the customize parameters list for the entry and start system (for Start Function) related items that can be customized via the audio and visual system vehicle customization screen (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).



b.

Confirm that it is possible to manually change the settings of the customize parameters for each system that are available for customization via the audio and visual system vehicle customization screen.

OK:

The items available for customization via the audio and visual system vehicle customization screen can be customized successfully using the manual procedure.




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)