Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. DTC Detection Condition Trouble Area
B1579 Microphone signal is lost.
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E307600E04
0.625,2.042 2.615,2.479 1.99,0.438 10 false Map Light Assembly (Telephone Microphone Assembly) 0.635,1.875 1.063,2.073 0.427,0.198 10 false U3 1.688,0.698 2.177,0.896 0.49,0.198 10 false SNS2 1.688,1.521 2.177,1.719 0.49,0.198 10 false MCO- 2.146,1.375 2.635,1.573 0.49,0.198 10 false 4 2.135,0.594 2.625,0.792 0.49,0.198 10 false 5 4.885,0.583 5.115,0.781 0.229,0.198 10 false 6 4.833,1.375 5.052,1.573 0.219,0.198 10 false 19 5.094,0.698 5.583,0.896 0.49,0.198 10 false SNS2 5.094,1.479 5.583,1.677 0.49,0.198 10 false MIN- 4.573,2.031 7.052,2.333 2.479,0.302 10 false Radio and Display Receiver Assembly 4.573,1.854 5,2.052 0.427,0.198 10 false L35

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U155186E03
2.073,1.969 2.365,2.604 false 0.135,0.073 0.344,0.292 0.208,0.219 10 false *a 1.594,0.698 1.958,0.896 0.365,0.198 10 false L35 2.26,2.625 2.635,2.823 0.375,0.198 10 false MIN-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the U3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-6 (SNS2) - U3-5 (SNS2) Always Below 1 Ω
L35-19 (MIN-) - U3-4 (MCO-) Always Below 1 Ω
L35-6 (SNS2) - Body ground Always 10 kΩ or higher
L35-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly) (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.
E187117E68
1.885,1.24 2.135,0.813 false 1.771,1.24 1.583,0.813 false 0.156,0.146 0.354,0.344 0.198,0.198 10 false *a 2.052,0.635 2.469,0.833 0.417,0.198 10 false MCO- 1.24,0.635 1.667,0.833 0.427,0.198 10 false SNS2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (SNS2) - 4 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map light assembly (Telephone Microphone Assembly))



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output




OK

END

NG

REPLACE MAP LIGHT ASSEMBLY