Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the radio and display receiver assembly and combination meter sub-assembly.

DTC No. DTC Detection Condition Trouble Area
B1324 After the radio and display receiver assembly receives a registration information signal, which is sent by the combination meter sub-assembly when the power switch is turned on (ACC), 1 or more times, the radio and display receiver assembly does not receive the signal for 30 seconds or more.
·

Combination meter sub-assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E361732E04
1.656,0.427 2.24,0.646 0.583,0.219 10 false MSCH 5.104,0.417 5.688,0.635 0.583,0.219 10 false CNH1 4.896,0.25 5.219,0.479 0.323,0.229 10 false 3 4.906,0.917 5.229,1.146 0.323,0.229 10 false 4 2.156,0.938 2.479,1.167 0.323,0.229 10 false 29 2.146,0.281 2.469,0.51 0.323,0.229 10 false 28 0.896,2.229 3.083,2.583 2.188,0.354 10 false : Local Bus Communication Line 0.604,1.552 1,1.781 0.396,0.229 10 false L27 0.594,1.719 3.031,2.052 2.438,0.333 10 false Combination Meter Sub-assembly 4.531,1.563 4.938,1.771 0.406,0.208 10 false L169 4.521,1.729 6.865,2.104 2.344,0.375 10 false Radio and Display Receiver Assembly 1.667,1.083 2.25,1.302 0.583,0.219 10 false MSCL 5.094,1.073 5.677,1.292 0.583,0.219 10 false CNL1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L169 radio and display receiver assembly connector.


b.

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L169-3 (CNH1) - L27-28 (MSCH) Always Below 1 Ω
L169-4 (CNL1) - L27-29 (MSCL) Always Below 1 Ω
L169-3 (CNH1) - Body ground Always 10 kΩ or higher
L169-4 (CNL1) - Body ground Always 10 kΩ or higher
L169-3 (CNH1) - L169-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L169-3 (CNH1) - Body ground Always Below 1 V
L169-4 (CNL1) - Body ground Always Below 1 V




OK

2.INSPECT COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER SUB-ASSEMBLY
a.

Remove the combination meter sub-assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.
E305050E09
1.885,1.927 1.635,2.333 false 2.01,1.938 2.208,2.344 false 1.385,2.344 1.854,2.688 0.469,0.344 10 false MSCL 2.146,2.365 2.615,2.708 0.469,0.344 10 false MSCH 0.146,0.25 0.615,0.594 0.469,0.344 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
28 (MSCH) - 29 (MSCL) Always 108 to 132 Ω


Text in Illustration
*a Component without harness connected
(Combination Meter Sub-assembly)



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER SUB-ASSEMBLY

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL).


b.
E286972E02
0.155,0.155 0.467,0.496 0.312,0.341 10 *a 2.323,1.135 2.793,1.476 0.470,0.341 10 CNH1 1.402,1.135 1.872,1.476 0.470,0.341 10 CNL1 2.349,1.339 2.106,1.746 false 1.803,1.336 1.997,1.746 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω


Text in Illustration
*a Component without harness connected
(Radio and Display Receiver Assembly)



OK

4.REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

5.CHECK METER / GAUGE SYSTEM

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK METER / GAUGE SYSTEM
a.

Turn the power switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch and check that the audio tab is displayed on the multi-information display in the combination meter sub-assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.




OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY