Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation ECU sub-assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation ECU sub-assembly cannot be operated using the steering pad switch assembly, and also the navigation ECU sub-assembly itself cannot function.

WIRING DIAGRAM

E250442E02
0.123,1.152 0.670,1.327 0.547,0.174 10 Volume- 1.727,3.793 2.313,3.968 0.586,0.174 10 Off hook 2.706,3.793 3.090,3.968 0.384,0.174 10 Voice 0.953,4.805 2.480,4.980 1.527,0.174 10 Steering Pad Switch LH 3.93,3.491 4.766,3.840 0.836,0.350 10 Steering Pad Switch RH 0.918,3.793 1.486,3.968 0.568,0.174 10 On hook 0.9,1.152 1.495,1.327 0.595,0.174 10 Volume+ 5.389,0.582 5.677,0.757 0.289,0.174 10 AU1 5.392,1.702 5.697,1.877 0.305,0.174 10 EAU 5.401,2.81 5.689,2.985 0.288,0.174 10 AU2 4.171,0.666 4.460,0.841 0.289,0.174 10 AU1 4.171,1.786 4.476,1.961 0.305,0.174 10 EAU 4.171,2.894 4.460,3.069 0.288,0.174 10 AU2 6.697,0.675 7.068,0.849 0.371,0.174 10 SW1 6.697,1.795 7.085,1.969 0.388,0.174 10 SWG 6.697,2.903 7.068,3.077 0.371,0.174 10 SW2 6.459,3.332 6.828,3.506 0.370,0.174 10 L38 3.93,3.332 4.300,3.506 0.370,0.174 10 SR1 1.735,1.152 2.199,1.327 0.464,0.174 10 Seek- 5.01,0.677 5.201,0.852 0.191,0.174 10 z9 5.01,1.797 5.201,1.972 0.191,0.174 10 z9 5.01,2.906 5.201,3.080 0.191,0.174 10 z9 5.013,0.496 5.189,0.670 0.176,0.174 10 10 5.045,1.616 5.143,1.790 0.098,0.174 10 8 5.045,2.724 5.143,2.898 0.098,0.174 10 9 5.826,0.677 6.120,0.852 0.294,0.174 10 L52 5.838,1.797 6.125,1.972 0.287,0.174 10 L52 5.838,2.906 6.119,3.080 0.281,0.174 10 L52 6.458,0.593 6.633,0.768 0.175,0.174 10 21 6.458,1.713 6.633,1.888 0.175,0.174 10 23 6.458,2.822 6.633,2.996 0.175,0.174 10 22 3.959,0.593 4.134,0.768 0.175,0.174 10 3 3.959,1.713 4.134,1.888 0.175,0.174 10 5 3.959,2.822 4.134,2.996 0.175,0.174 10 4 5.921,1.616 6.019,1.790 0.098,0.174 10 4 5.909,0.496 6.007,0.670 0.098,0.174 10 6 5.921,2.724 6.019,2.898 0.098,0.174 10 5 2.332,2.346 2.769,2.520 0.437,0.174 10 MODE 5.11,3.332 6.011,3.963 0.901,0.631 10 Spiral Cable with Sensor Sub-assembly 6.459,3.5 7.150,4.232 0.691,0.732 10 Navigation ECU Sub-assembly 2.36,1.152 2.824,1.327 0.464,0.174 10 Seek+

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the L38 navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-21 (SW1) - L38-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
L38-22 (SW2) - L38-23 (SWG) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Disconnect the z9 steering pad switch assembly connector.

U191357E02
3.677,2.698 3.677,3.042 false 4.031,3.042 3.792,2.698 false 3.344,3.042 3.573,2.698 false 1.667,1.25 2.156,0.76 false 1.677,1.583 2.208,1.854 false 1.396,1.573 1.052,1.833 false 1.396,1.229 1.094,0.927 false 1.469,1.406 0.906,1.302 false 1.688,2.063 1.271,2.49 false 1.771,2.313 1.313,2.771 false 1.865,2.51 1.406,2.969 false 2.927,2.458 3.094,2.625 0.167,0.167 10 false z9 3.542,3.052 3.865,3.24 0.323,0.188 10 false AU2 3.938,3.052 4.26,3.24 0.323,0.188 10 false AU1 3.135,3.063 3.458,3.25 0.323,0.188 10 false EAU 0.156,0.094 0.313,0.281 0.156,0.188 10 false *a 2.156,0.635 2.313,0.823 0.156,0.188 10 false *b 0.948,0.792 1.104,0.979 0.156,0.188 10 false *d 0.75,1.208 0.906,1.396 0.156,0.188 10 false *f 0.896,1.781 1.052,1.969 0.156,0.188 10 false *e 2.219,1.792 2.375,1.979 0.156,0.188 10 false *c 1.156,2.698 1.313,2.885 0.156,0.188 10 false *h 1.292,2.906 1.448,3.094 0.156,0.188 10 false *i 1.094,2.406 1.25,2.594 0.156,0.188 10 false *g


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-10 (AU1) - z9-8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 323 to 335 Ω
Volume+ switch pushed 980 to 1020 Ω
Volume- switch pushed 3048 to 3172 Ω
z9-9 (AU2) - z9-8 (EAU) No switch pushed 95 to 105 kΩ
MODE switch pushed Below 2.5 Ω
On hook switch pushed 323 to 335 Ω
Off hook switch pushed 980 to 1020 Ω
Voice switch pushed 3048 to 3172 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Seek+
*c Seek- *d Volume+
*e Volume- *f MODE
*g Voice *h On hook
*i Off hook - -


c.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
NG A
OK B




A

3.INSPECT STEERING PAD SWITCH RH

B

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
3.INSPECT STEERING PAD SWITCH RH
a.

Disconnect the z9 steering pad switch RH connector.


b.

Disconnect the SR1 steering pad switch RH connector.

U191380E02
3.677,2.729 3.417,2.99 false 3.771,2.729 3.771,2.99 false 3.896,2.729 4.135,2.979 false 1.688,1.469 1.438,1.719 false 1.823,1.469 1.823,1.719 false 1.969,1.469 2.219,1.708 false 0.167,0.156 0.417,0.385 0.25,0.229 10 false *a 2.854,2.552 3.104,2.781 0.25,0.229 10 false z9 3.146,2.99 3.458,3.135 0.313,0.146 10 false EAU 3.646,2.99 3.958,3.135 0.313,0.146 10 false AU2 4.073,2.99 4.385,3.135 0.313,0.146 10 false AU1 0.729,1.354 1.042,1.583 0.313,0.229 10 false SR1 1.167,1.729 1.479,1.875 0.313,0.146 10 false AU1 1.698,1.729 2.01,1.875 0.313,0.146 10 false AU2 2.146,1.729 2.458,1.875 0.313,0.146 10 false EAU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SR1-3 (AU1) - z9-10 (AU1) Always Below 1 Ω
SR1-5 (EAU) - z9-8 (EAU) Always Below 1 Ω
SR1-4 (AU2) - z9-9 (AU2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Steering Pad Switch RH)
- -



OK

REPLACE STEERING PAD SWITCH LH

NG

REPLACE STEERING PAD SWITCH RH

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Disconnect the z9 steering pad switch assembly connector.


b.

Disconnect the L52 spiral cable with sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

E343950E01
3.417,3.5 3.833,3.75 0.417,0.25 3.583,0.333 4,0.583 0.417,0.25 3.458,1.25 3.625,1.083 false 3.365,4.365 3.667,4.115 false 3.74,1.24 3.771,1.073 false 3.865,4.375 3.802,4.115 false 4.188,4.344 3.927,4.115 false 4,1.229 3.875,1.073 false 1.656,0.313 1.969,0.51 0.313,0.198 10 false *a 3.031,0.271 3.344,0.469 0.313,0.198 10 false *b 3.719,0.375 4.031,0.573 0.313,0.198 10 false z9 2.813,3.427 3.125,3.625 0.313,0.198 10 false *c 3.51,3.552 3.969,3.75 0.458,0.198 10 false L52 3.292,1.25 3.656,1.448 0.365,0.198 10 false AU1 3.615,1.25 3.979,1.448 0.365,0.198 10 false AU2 3.938,1.26 4.302,1.458 0.365,0.198 10 false EAU 3.229,4.396 3.594,4.594 0.365,0.198 10 false EAU 3.719,4.406 4.083,4.604 0.365,0.198 10 false AU2 4.104,4.396 4.469,4.594 0.365,0.198 10 false AU1

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z9-10 (AU1) - L52-6 (AU1) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right
z9-9 (AU2) - L52-5 (AU2) Center Below 3 Ω
2.5 rotations to the left
2.5 rotations to the right



d.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Always Below 3 Ω
z9-10 (AU1) - L52-6 (AU1) Always Below 3 Ω
z9-9 (AU2) - L52-5 (AU2) Always Below 3 Ω


NOTICE:
·

The spiral cable with sensor sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable with sensor sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.



HINT:


Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY