Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301800 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84307 1.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the negative (-) auxiliary battery cable connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the negative (-) auxiliary battery cable connected and the power switch on (IG).

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

·

Do not remove the spiral cable from the steering sensor.



a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.


c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch pin may snap.



e.

Engage the 3 claws to install the spiral cable with sensor sub-assembly.

NOTICE:

When replacing the spiral cable with sensor sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



f.

Connect the connectors to the spiral cable with sensor sub-assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



Hide 3. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 84307 4.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check if the spiral cable with sensor sub-assembly is centered.

OK:
·

The connector is positioned at the top.

·

The colored roller or flat cable can be seen in the inspection window.


B503333C01
0.938,1.083 0.938,0.719 0.938,0.719 0.552,0.719 true 4.354,1.083 4.354,0.719 4.354,0.719 3.969,0.719 true 4.406,1.198 4.406,1.615 4.406,1.615 4.021,1.615 true 0.958,1.229 0.958,1.604 0.958,1.604 0.573,1.604 true 0.292,0.052 0.604,0.208 0.313,0.156 10 false *A 3.74,0.083 4.052,0.24 0.313,0.156 10 false *B 0.385,0.625 0.698,0.781 0.313,0.156 10 false *a 0.406,1.51 0.719,1.667 0.313,0.156 10 false *b 3.865,1.51 4.177,1.667 0.313,0.156 10 false *c 3.823,0.625 4.135,0.781 0.313,0.156 10 false *a
*A Colored Roller Type *B Flat Cable Type
*a Inspection Window *b Colored Roller
*c Flat Cable - -



d.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Make sure to observe the following precautions, otherwise the spiral cable with sensor sub-assembly may be damaged.

·

Do not rotate the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not rotate the spiral cable with sensor sub-assembly with excessive force.



i.
B503334

Rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the spiral cable with sensor sub-assembly is rotated clockwise in this step, it may be damaged and may no longer be able to be centered. Make sure to only rotate the spiral cable with sensor sub-assembly counterclockwise.



ii.
B503335

If the connector is not positioned at the bottom of the rotation of the spiral cable with sensor sub-assembly when the spiral cable with sensor sub-assembly is turned until it stops, turn the spiral cable with sensor sub-assembly clockwise until the connector is positioned at the bottom as shown in the illustration.


iii.
B503336

Rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times.

NOTICE:

If the spiral cable with sensor sub-assembly is rotated clockwise 5 times or more from the point at which it stops and the connector is positioned at the bottom, the spiral cable with sensor sub-assembly may be damaged.



iv.

Check that the spiral cable with sensor sub-assembly is centered.

OK:
·

The connector is positioned at the top.

·

The colored roller or flat cable can be seen in the inspection window.


B503333C01
0.938,1.083 0.938,0.719 0.938,0.719 0.552,0.719 true 4.354,1.083 4.354,0.719 4.354,0.719 3.969,0.719 true 4.406,1.198 4.406,1.615 4.406,1.615 4.021,1.615 true 0.958,1.229 0.958,1.604 0.958,1.604 0.573,1.604 true 0.292,0.052 0.604,0.208 0.313,0.156 10 false *A 3.74,0.083 4.052,0.24 0.313,0.156 10 false *B 0.385,0.625 0.698,0.781 0.313,0.156 10 false *a 0.406,1.51 0.719,1.667 0.313,0.156 10 false *b 3.865,1.51 4.177,1.667 0.313,0.156 10 false *c 3.823,0.625 4.135,0.781 0.313,0.156 10 false *a
*A Colored Roller Type *B Flat Cable Type
*a Inspection Window *b Colored Roller
*c Flat Cable - -


NOTICE:

If the spiral cable with sensor sub-assembly cannot be centered, it may be damaged. Replace the spiral cable with sensor sub-assembly with a new one.




Hide 45100 5.INSTALL STEERING WHEEL ASSEMBLY