This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly*1 ·
Stereo component amplifier assembly*2 |
*1: for 6 Speakers
*2: for 8 Speakers
for 6 Speakers
for 8 Speakers
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 8 Speakers | B |
A
B
Disconnect the L167 and L166 radio and display receiver assembly connectors.
Disconnect the I2 and I3 front No. 2 speaker assembly connectors.
Disconnect the P3 and Q3 rear speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L167-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| L167-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| L167-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| L167-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| L166-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| L166-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| L166-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| L166-6 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the I2 and I3 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I2-1 (+) - Body ground | Always | 10 kΩ or higher |
| I2-3 (-) - Body ground | Always | 10 kΩ or higher |
| I3-1 (+) - Body ground | Always | 10 kΩ or higher |
| I3-3 (-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
OK
NG
Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (+) - 4 (-) | Always | 10 kΩ or higher |
| 1 (+) - 2 (+) | Always | Below 1 Ω |
| 3 (-) - 4 (-) | Always | Below 1 Ω |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
OK
NG
Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Rear Speaker Assembly) |
OK
NG
Disconnect the L30 stereo component amplifier assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the I4 and I5 front No. 2 speaker assembly connectors.
Disconnect the P3 and Q3 rear speaker assembly connectors.
Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L30-15 (WFR+) - Body ground | Always | 10 kΩ or higher |
| L30-30 (WFR-) - Body ground | Always | 10 kΩ or higher |
| L30-8 (WFL+) - Body ground | Always | 10 kΩ or higher |
| L30-23 (WFL-) - Body ground | Always | 10 kΩ or higher |
| L30-9 (FR+) - Body ground | Always | 10 kΩ or higher |
| L30-24 (FR-) - Body ground | Always | 10 kΩ or higher |
| L30-14 (FL+) - Body ground | Always | 10 kΩ or higher |
| L30-29 (FL-) - Body ground | Always | 10 kΩ or higher |
| L30-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| L30-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| L30-11 (RL+) - Body ground | Always | 10 kΩ or higher |
| L30-26 (RL-) - Body ground | Always | 10 kΩ or higher |
| L30-13 (TWR+) - Body ground | Always | 10 kΩ or higher |
| L30-28 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L30-10 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L30-25 (TWL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4.6 to 6.6 Ω |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
OK
NG
Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
OK
NG
Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 5.2 Ω |
| *a | Component without harness connected
(Rear Speaker Assembly) |
OK
NG
Remove the rear No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
OK
NG